Polygroup MTS-801 Assembly Instructions

ROTATING TREE STAND ASSEMBLY INSTRUCTIONS
Congratulations on purchasing your new rotating tree stand from Polygroup®! Carefully follow the instructions
below on how to quickly and easily set up your new stand.
Fig.A Fig.B
Power cord to wall outlet
On/Off
Switch
Fig.C Fig.D
Yellow
Label
1. Before you start to assemble your tree with rotating tree stand, choose an appropriate location near a wall outlet.
2. Before using or reusing inspect product carefully. Discard any products that have cut, damaged, or frayed wire
insulation or cords, cracks in the lampholders or enclosures, loose connections, or exposed copper wire.
3. Slide the four stand legs upward into slots at the base of the stand until secure. (Fig. A)
4. Place assembled rotating tree stand on a level surface.
5. Insert your Christmas tree's metal pole into the rotating tree stand (need match Adaptor Ring inserts for 1.25" / 1").
HINT: Insert your Christmas tree's bottom section ONLY into the rotating tree stand first and then continue with the
remaining section to minimize heavy lifting. (Fig. B)
6. Plug in your Christmas tree lights into the yellow labeled outlet receiver on the rotating tree stand. (Fig. C)
7. Plug in the green labeled rotating tree stand plug into wall outlet. (Fig. D)
8. Switch on the motor at the tree stand when you want the tree to revolve. To keep the tree stay still switch off the motor.
9. Turn on the power switch on the rotating tree stand. Your entire tree should now be lit and rotating. (Fig. E) If some
bulbs do not light or flicker, please refer to your Christmas tree's instruction manual.
IMPORTANT SAFETY INSTRUCTIONS
When using electrical products, basic precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
1.
2. FOR INDOOR USE ONLY. USE ONLY WITH AN ARTIFICIAL TREE. THIS STAND DOES NOT CONTAIN A WELL FOR WATER.
3. Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are used
in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not
provided, contact a qualified electrician for proper installation.
4. This seasonal use product is not intended for permanent installation or use.
5. Do not mount or place near gas or electric heaters, fireplaces, candles or other similar sources of heat.
6. Do not secure the wiring of product with staples or nails, or place on sharp hooks or nails.
7. Do not let lamps rest on the supply cord or on any wire.
8. Unplug the product when leaving the house, when retiring for the night, or if left unattended.
9. This is an electric product-not a TOY! To avoid risk of fire, burns, personal injury and electric shock it should not be
played with or placed where small children can reach it.
10. Do not use this product for other than its intended use. The stand is to be used just for the Christmas tree.
11. Do not hang ornaments or other objects from cord, wire, or light string.
12. Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
1.5"
1.25" 1"
Fig.E
Green
Label
13. Do not cover the product with cloth, paper or any material not part of the product when in use.
14. This product has a polarized plug (one blade is wider than the other) as a feature to reduce the risk of electric
shock. This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician. Do not use with an extension cord unless plug can be
fully inserted. Do not alter or replace the plug.
15. This product employs overload protection (fuse). A blown fuse indicates an overload or short- circuit situation.
If the fuse blows, unplug the product from the outlet. Also unplug any additional strings or products that may
be attached to the product. Replace the fuse as per the user servicing instructions. Follow product marking for
proper fuse rating and check the product. If the replacement fuse blows, a short-circuit may be present and the
product should be discarded.
16. Max loading current / power: 3.4 A / 408 W. Electrical Rating for the Stand: AC120V 60Hz Max 0.045A.
17. Load of tree: Max. 90 lbs. Height of Tree: Max. 9.0 feet.
18. Read and follow all instructions that are on the product or provided with the product.
SAVE THESE INSTRUCTIONS.
USE AND CARE INSTRUCTIONS
1. When storing the tree stand, carefully remove all other products including the Christmas tree, branches, or bushes,
to avoid any undue strain or stress on the product's conductors, connections and wires.
2. When not in use, store neatly in a cool, dry location protected from sunlight.
3. Before using or reusing inspect product carefully. Discard any products that have cut, damaged, or frayed wire
nsulation or cords, loose connections, or exposed copper wire.
USER SERVICING INSTRUCTIONS
FUSE REPLACEMENT
1. Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord.
2. Open fuse cover, slide open fuse access cover on top of attachment plug towards blades.
3. Remove fuse carefully, turn fuseholder over and remove fuse.
4. Risk of fire. Replace fuse only with 5 or 8 Amp, 125 Volt fuse for the
power cord set. Correct fuse current value is written on the plug hosing.
5. Close fuse cover. Slide closed fuse access cover on top of attachment plug.
6. Risk of fire. Do not replace attachment plug. Contains a safety device (fuse)
that should not be removed. Discard product if the attachment plug is
damaged.
SPARE PARTS
Each rotating tree stand includes the following:
1 x stand base
4 x stand legs
1 x extra fuse located in the green labeled wall outlet plug
If extra parts are needed, please contact our customer service center.
For any questions, assistance, or missing parts, Do Not Return To Place Of Purchase. Please contact
us at 1-888-919-0070 or visit our website at www.polygroupstore.com. One of our customer
service representatives will be happy to assist you.
ETL Model # MTS-801
SKU# 5168331
SPARE FUSE