Advertisement
2.2.
Specification
Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IRC153.V4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IRS153.V4
Power output (2 heat settings) . . . . . . . . 1500/3000 Watt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1500/3000 Watt
Size W X D X H. . . . . . . . . . . . . . . .560 x 490 x 885mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .600 x 620 x 815mm
Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18kg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13kg
Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V (50Hz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230V (50Hz)
3.
ASSEMBLY
3.1.
IRC153.V4
Fig.1.
3.1.1. Attach the wheel sub-assemblies
to the base of the heater using
the bolts provided. Ensure the
lockable wheels are to the rear
of the heater.
3.1.2. Attach the handle to the top of
the heater using the bolts
provided, ensuring the shaped
spacers are fitted between the
heater and the handle as shown.
3.1.3 Remove the front grille by
unscrewing the retaining
screws.
3.1.4 Extract the lamps from the
shipping carton.
NEVER TOUCH LAMP
GLASS DIRECTLY WITH
FINGERS, ONLY TOUCH
THE CERAMIC ENDS OR
USE A SOFT CLOTH,
OTHERWISE LAMPS COULD
BE DAMAGED!
3.1.5 Carefully insert each
lamp into the two push-in
side fittings with a gentle
pressure.
3.1.6 Check the lamps are properly
located.
3.1.7 Reassemble front grille.
4.
HEATER OPERATION
4.1.
Operating the heater.
4.1.1. Place the heater on a level floor in a suitable position in the area you require to heat. Allow a minimum of 2mtr between the heater and adjacent objects.
4.1.2. Plug the heater into the mains supply.
4.1.3. Select the required output by using the two rocker switches on the side which switch the lamps on and off. Each lamp has an output of 1500W.
4.1.4. To switch the unit off, select "0" on both the rocker switches and unplug from the mains. Allow the unit to cool before handling or storage.
Ë
WARNING! DO NOT touch the top of the heater when in use as it becomes hot.
Ë
WARNING! Always allow lamps to cool before moving the units. Use only on a smooth even surface. Failure to do so will cause premature wear to
the lamps and reduce their working life.
4.2.
Tilt switch safety mechanism.
4.2.1. The heater has a built in tilt switch safety mechanism that switches off the unit if it is tilted beyond 25° either forwards or backwards. This prevents fire in the
event of the unit being knocked over. If the unit does not turn on again when returned to the vertical, tip it approximately 25° in the opposite direction until
you hear the internal switch operate. As the heater switches on return it to the vertical position.
5.
MAINTENANCE
Ë
WARNING! Before attempting any maintenance ensure the unit is unplugged from the mains power supply, it is cool and it is on level ground.
DO NOT touch the lamp glass, even when cold.
DO NOT use the heater without the grilles fitted.
5.1.
Cleaning.
5.1.1. To clean the reflector, remove the grille by unscrewing the retaining screws and wipe the reflector with a clean dry cloth. DO NOT use abrasives or
solvents. The surface of the reflector is very soft and scratches may cause it to overheat. Replace the grille.
5.2.
Changing a lamp.
5.2.1. Remove the front grille by unscrewing the retaining screws.
5.2.2. Ease the sprung sockets on the ends of the lamp back and pull the lamp forward such that it clears the sockets.
5.2.3. Remove the lamp from the sockets.
5.2.4. NEVER TOUCH THE LAMP GLASS DIRECTLY WITH FINGERS, ONLY TOUCH THE CERAMIC ENDS OR USE A SOFT CLOTH, OTHERWISE THE
LAMP COULD BE DAMAGED!
5.2.5. Carefully insert the replacement lamp into the two push-in side fittings with a gentle pressure.
5.2.6. Check the lamp is properly located.
5.2.7. Reassemble front grille.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
Fig 1
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
Original Language Version
3.2.
IRS153.V4 Fig.2.
3.2.1. Fit the handle section of the support
frame to the wheel section
ensuring the fixing holes
align.
3.2.2. Fit the heater to the
support frame using the bolts
provided, ensuring the
shaped spacers are fitted
either side of the frame as
shown. Tighten the bolts
sufficiently to retain the
heater at the required angle.
3.2.3 Remove the front grille by
unscrewing the retaining
screws.
3.2.4 Extract the lamps from the
shipping carton.
NEVER TOUCH LAMP
GLASS DIRECTLY WITH
FINGERS, ONLY TOUCH
THE CERAMIC ENDS OR
USE A SOFT CLOTH,
OTHERWISE LAMPS
COULD BE DAMAGED!
3.2.5 Carefully insert each
lamp into the two push-in
side fittings with a gentle
pressure.
3.2.6 Check the lamps are properly located.
3.2.7 Reassemble the front grille.
01284 757500
01284 703534
Fig 2
www.sealey.co.uk
Web
sales@sealey.co.uk
email
IRC153.V4, IRS153.V4
Issue No.2
09/11/09
Advertisement
