Cleaning And Sanitizing; Daily Cleaning - H.C Duke & Son ELECTRO FREEZE Arctic Swirl HDM75A Operator's Manual

Hide thumbs

Table Of Contents

Table of Contents

ELECTRO FREEZE Arctic Swirl Model HDM75A

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5

Cleaning and Sanitizing

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5

The spindle shaft, agitator (exposed

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5

turning portion) and splash guards must

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5

be washed, rinsed, sanitized, air dried,

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5

and prepared for use at the end of each

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5

day of operation.

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5

The operator should have clean hands

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5

and refrain from coughing or sneezing

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5

on parts to avoid contamination. Do not

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5

allow any of the Arctic Swirl mixer parts

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5

to come into contact with objects that

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5

have not been sanitized.

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5

When cleaning or sanitizing the spindle

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5

shaft and agitator, use a lower speed

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5

setting than used for blending to prevent

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5

water or sanitizing solution from splash-

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5

ing out of the cup.

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5

4.1

Daily Cleaning

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5

full with a solution of warm soapy water

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5

(100°F or 37.8°C) and hold it under the

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5

spindle.

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5

setting of 20-30 on the speed control

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5

dial.

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5

To avoid injury, never place a towel or any other material

on the rotating shaft to clean it. Unplug unit before clean-

ing.

Rotating metal shaft. To avoid injury, use only paper or

plastic mixing containers. Contact between shaft and

metal containers or malt collars can cause shaft to wear

and break.

1. Fill a paper cup or shake cup ¾

2. To clean, operate the spindle at a

Never place a towel or any other

material on the shaft to clean it when

it is placed in the "ON" or "JOG"

position. If the material becomes

caught, it will damage the machine.

Do not allow water above the collar

on the top portion of the Arctic Swirl

shaft. Water in this area may damage

the machine.

CAUTION

3. Stop the spindle operation and

use a small brush to clean areas around

the agitator.

4. Rinse with clean water.

H.C. Duke & Son, Inc.

Important:

184915

Table of Contents