Advertisement
500 Watt Portable
Halogen
Work Light
SHL10
ASSEMBLY INSTRUCTIONS
Do not assemble while plugged into power.
1. Insert stand base (1) into other end of tube. Use the stand handle (2) to position the
lamp to the desired angle. Insert and tighten angle adjustment knob (3).
2. L amp angle may be altered simply by loosening the angle adjustment knob (3),
moving the stand handle to bring the lamp to the desired angle, then tightening the angle fixing knob.
1
INSERTING OR REPLACING HALOGEN LAMP
Important: Ensure unit is disconnected from power point. Allow time for unit to cool before handling.
1. Unscrew retaining screw on top of lamp. This will release the protective grid, front
surround and glass faceplate.
2. Lower front surround down. It will be retained by the hinges.
3. To insert halogen globe, unwrap globe, taking care your fingers do not touch the
globe. Use wrapping to handle the globe. Push one end of globe into either of the
spring-loaded sockets. Locate other end on other socket, & release.
4. Carefully replace front surround, making sure that it is correctly positioned.
Screw up tightly.
Recommended replacement tube is Intex #SHT50, 500 Watt Tungsten Halogen
Lamp or similar 118mm long halogen lamps.
1
intexinternational.com
Copyright © 2020 Intex International.
Site Equipment
2
2
4
3
Building Excellence
Advertisement
Table of Contents
Related Manuals for Intex SHL10
Summary of Contents for Intex SHL10
- Page 1 Important: Ensure unit is disconnected from power point. Allow time for unit to cool before handling. 1. Unscrew retaining screw on top of lamp. This will release the protective grid, front surround and glass faceplate. 2. Lower front surround down. It will be retained by the hinges. 3. To insert halogen globe, unwrap globe, taking care your fingers do not touch the globe. Use wrapping to handle the globe. Push one end of globe into either of the spring-loaded sockets. Locate other end on other socket, & release. 4. Carefully replace front surround, making sure that it is correctly positioned. Screw up tightly. Recommended replacement tube is Intex #SHT50, 500 Watt Tungsten Halogen Lamp or similar 118mm long halogen lamps. intexinternational.com Building Excellence Copyright © 2020 Intex International.
- Page 2 - Do not operate with cracked or missing glass face. - Do not allow children to play in its proximity. WARNINGS FAILURE TO OBSERVE THE ABOVE SAFETY INSTRUCTIONS COULD RESULT IN FATAL ELECTRIC SHOCK AND OTHER HAZARDS. intexinternational.com Building Excellence Copyright © 2020 Intex International.
- Page 3 1 x 500 Watt (150 Watt) (SINGLE HEAD) Follow the same instructions as 2 X 500W except that point 2 & 3 change to as following: Mount the fixture assembly to the top of the telescope pole by turning centre knob clockwise until secure as shown in Fig. 5. Do not over-tighten the centre knob. FIG 4 ***WARNING*** 1. This fixture is GS listed and safe when used in a careful manner. 2. Fixture heads get very hot and should not be used within 18” of combustible materials such as paper, cardboard, wood or fabric to avoid starting a fire. 3. Do not use this fixture near combustible materials such as gasoline to avoid explosion. Always unplug the fixture before doing any work or when changing the bulb. 4. In event that you need to move the fixture to the next job site or change a bulb, ample time should be FIG 5 given to cool as fixture head gets very hot. 5. Never point the fixture directly at a person’s eyes. 6. Do not touch the halogen bulb when installing it in the fixture as oil from your skin will shorten the bulb life significantly. Best to use a clean cloth to install the bulb. 7. Never touch the fixture when power is on because surface is hot and can cause severe burns. ***BULB INSTALLATION*** 1. Use max. 500W T-3 halogen bulb. 2. Disconnect power and allow bulb to cool prior to installation. 3. Use screwdriver to release the frame and remove old bulb. Push gently toward the right side of the socket until left side is clear from socket and can be removed by moving forward. 4. To install bulb, only use clean gloves or cloth. Fit the bulb into side goes into its socket, allow left end to be inserted into left hand side of socket. 5. Never turn power on with hinge door open. intexinternational.com Building Excellence Copyright © 2020 Intex International.
- Page 4 - Do not operate with cracked or missing glass face. - Do not allow children to play in its proximity. WARNINGS FAILURE TO OBSERVE THE ABOVE SAFETY INSTRUCTIONS COULD RESULT IN FATAL ELECTRIC SHOCK AND OTHER HAZARDS. intexinternational.com Building Excellence Copyright © 2020 Intex International.
Need help?
Do you have a question about the SHL10 and is the answer not in the manual?
Questions and answers