Subscribe to Our Youtube Channel
Related Manuals for Yard-Man 7200-0
Summary of Contents for Yard-Man 7200-0
- Page 1 MAN CO.. P. O. BOX 36940 CLEVELAND, OHIO 44136 1410 West Ganson Street -Jackson, Michigan 49202 0611-7588 PRINTED !N U.S.A. " YARD.
- Page 2 Your SNOW THROWER is a precision piece of snow throwing equipment. Engineering skill and experience have been combined to provide the ultimate in safety and efficiency. As with any type of power equipment, carelessness or error on the part of the operator can result in injury.
-
Page 3: Maintenance
GENERAL SNOW~THROWING 1.~ Always keep area to be cleaned cleared before~owfall~. 2.~. Always start engine with machine on level surface with master clutch disengaged: After starting, let engine warm up several minutes at slow speed before starting to remove ~now~ Ifinachine is stored indoors, let engine and machine adjust to outdoor temperatures before starting to throw snow': ..'co When throwing snow, ~u!:, machln.eat.~ull throttl~ for best re~lts:... - Page 4 AND SET-UP 1. Before assembling your Snow Thrower be sure all hardware, parts, and instructions have been removed from the carton..:' ':;.' Assemble right and left handle tubes to the unit with bolts, lockwashers, and flat washers. Do not tighten.3. Assemble handle panel assembly to the under side of right and left handle tubes and secure with four slotted hex head bolts and lock nuts.
-
Page 5: Before Starting Engine
BEFORE STARTING ENGINE 1. Fill the fuel tank with fresh winter blend regular gaso- line. DO NOT MIX OIL WITH GASOLINE. certain the fuel shut-off valve under the gas tank is turned on. 2. Place machine on a level surface. Remove oil fill cap and fill crankcase with good quality detergent oil. -
Page 6: Operation Of Controls
OPERATION OF CONTROL MASTERCLUrCH The master clutch control is located on handle panel and IS used to engage, all power~Select:8 forward speed or rever~ " ",,'c,';""...c"":, with shift lever, then release master clutch control and push ,," f,orward to engage ?rive diS?: f~~: reel. To disengage, pu II master clutch control back and lock in notch. - Page 7 REPLACING SAFETY SHEAR BOLT If the intake snow reel should jam causing the safety shear bolt to shear, it may be replaced with a new bolt, furnished in the parts bag, after removing the broken pieces in the shaft. NOTE: Always align the hole in the reel shaft and the sprocket shaft before driving out the broken bolt.
- Page 10 1513-113 Bol1- Shoulder 1/4-20 1513-125 Bolt -Shoulder 1/4-20 Grade 5 2118-58 Assembly -Chain Cover 1539-90 Nut -Speed Grip 1/4-20 PARTS LIST MODEL 7200-0 3622-122 \."..- 3765-6 2168-55 " 1654-35 111 '3150-17 112 ~'41362 " 113 ':; 3120-70 114' 1509-126 ,,;;,.
-
Page 11: Parts List
REF. PART DESCRIPTION 1654-31 Chain -W/Connactlng No.41 x 28 pitches 1624-192 Spacer-Gear Sprocket 1652-114 Baaring-Needla7/16x 1149-5 A-mbly -Gaar & Sprocket W/Bearlng (Included Ref. No.3) 42342 Nut -Hex Lock 3/8.16 (Eslok) 1008 Washer -SA.E. 1646-24 Key -Woodruff 3/32 x 5/8 2638-51 Sprocket -aT 1624-191 Spacer -Sprocket... - Page 12 NOTE: Make adjustments with ..., and wire removed from th~- sparkplug. (Fasten wire to cylinder head at least 1 away.from sparkplug.) IDLER LINKAGE ADJUSTMENT .:.~. Should the drive belt stretch enough to prevent the ad justment link from moving freely in the idler arm, slot, with the master clutch lever in drive position, adjust' as follows.
-
Page 13: Changing Engine Oil
LUBRICA TION- CHANGING ENGINE OIL Drain oil when engine is warm. To drain oil, place pan under frame directly beneath oil drain extension. Remove oil drain cap and allow oil to drain completely. Replace drain cap and tighten securely. Refill to "Full", mately 1 pint. - Page 14 CHUTE CABLE REPLACEMENT OR REPAIR 1. REMOVE BLOWER HOUSIN~ MACHINE. A. Remove the ~ain guard and disconnect the reel drive chain at the chain connecting link. B. Re!:':1°ve the !.Ou! carriage- bolts, fastening the scoop to the mounting brackets. Remove the: scoop and -.,' .,,'"...
- Page 15 .~';:;j...
- Page 16 30" SNOW THROWER enjoy these outstanding features 7/73...
Need help?
Do you have a question about the 7200-0 and is the answer not in the manual?
Questions and answers