STAGE 4 – CONTROL TUBE features that do not exist on any other portable STAGE 5 – UPRIGHTS chainsaw mill in the world. Panther Chainsaw Mills STAGE 6 – ASSEMBLY OF ALL SECTIONS 10 –11 are designed and built in the UK to the highest 60"...
Page 3
42" PANTHER HORIZON MASTER COMPONENT LIST ITEM PART DESCRIPTION AMOUNT IMAGE NUMBER NUMBER ITEM PART CM003 Rack Mount BKT DESCRIPTION AMOUNT IMAGE NUMBER NUMBER CM001B Hex Bolt M8 x 65mm CM004A Pinion Block CM001H Hex Screw Flanged M8 x 12mm (2 of these are optional)
42" STAGE 1 – CROSS RAILS Take the following parts Loosen all Grub Screws as shown by turning the Item 19 x 2 Cross Braces Allen Key anti clockwise. Item 30 x 8 Corner Brackets Small Allen Key Insert 2 Corner Brackets into Use the other Cross the Cross Brace end ensuring Brace as a guide sliding...
Plastic Insert facing down. Then add the Adjustable Handle on the same side as the Push Handle Panther logo and the Nyloc Nut M8 on the opposite side. Cross Rail Do not fully tighten the nut you can do this later. Repeat this step so you have x 2 assembled Rack Mounts.
42" STAGE 4 – CONTROL TUBE 42" STAGE 5 – UPRIGHTS Take the following parts Item 7 x 4 Plain Washers M6 Item 9 x 4 Sock Cap Screw M6 x 45mm Item 21 x 2 Pinion Blocks Take the following parts Item 23 x 1 Control Tube Item 4 x 2 Nyloc Nuts M8 Flange Item 26 x 1 Stop Boss...
Uprights so that they are the same. Before using the Panther Mill please ensure that you perform a final check of all fastenings to make sure everything is safe to use.
Page 8
60" / 72" / 84" PANTHER HORIZON MASTER COMPONENT LIST 60" PANTHER HORIZON MASTER COMPONENT LIST ITEM PART ITEM PART DESCRIPTION AMOUNT IMAGE DESCRIPTION AMOUNT IMAGE NUMBER NUMBER NUMBER NUMBER CM001B Hex Bolt M8 x 65mm CM029 Plastic Insert CM031...
60" STAGE 1 – CROSS RAILS Take the following parts Loosen all Grub Screws as shown by turning the Item 49 x 3 Cross Braces Allen Key anti clockwise Item 51 x 12 Corner Brackets Small Allen Key. Insert 2 Corner Brackets into Use the other Cross the Cross Brace end ensuring Brace as a guide sliding...
Slide on the Rack Clamp, then the 2 x Plain Washer M8. Plastic Insert facing down. Then add the Adjustable Handle on the same side as the Panther logo and the Nyloc Nut M8 on the opposite side. Pinion Block Push Handle Do not fully tighten the nut you can do this later.
60" STAGE 4 – CONTROL TUBE 60" STAGE 5 – UPRIGHTS Take the following parts Take the following parts Item 7 x 6 Plain Washers M6 Item 4 x 2 Nyloc Nuts M8 Flange Item 9 x 6 Sock Cap Screw M6 x 45mm Item 6 x 2 Plain Nuts M8 Item 26 x 1 Stop Boss Item 10 x 2 Spring Washers M8...
Uprights so that they are the same. Before using the Panther Mill please ensure that you perform a final check of all fastenings to make sure everything is safe to use.
Page 13
Chainsawbars Unit 2 Brookside Farm Agars Lane Silver Street Hampshire SO41 0FL UK England T. +44 (0)1590 681 259 You can also text or WhatsApp us on M. +44 (0)7508 276 769 www.chainsawbars.co.uk...