Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Cardioline XR600R
Summary of Contents for Cardioline XR600R
- Page 1 xr 600 r User Manual Rev. 02 – 20.06.2017...
- Page 2 600 r All rights reserved © Cardioline SpA. CARDIOLINE® is a registered trademark of Cardioline SpA. This publication may not be reproduced, in whole or in part, in any form or manner, without prior written authorisation Cardioline SpA Via Linz, 151 38121 Trento –TN-...
-
Page 3: Table Of Contents
User description ..........................10 4.3. Treadmill uses ..........................10 4.4. Emergency ............................10 SOFTWARE ...............................12 5.1. Connection to ECG ...........................12 5.2. Setup ..............................12 5.3. Extraordinary lubrication .........................14 5.4. Oil can substitution ..........................14 TECHNICAL DESCRIPTION .........................15 6.1. Technical specifications ........................15 6.2. Connecting cable ..........................16 www.cardioline.it... - Page 4 The running belt stops and restarts ....................20 9.2. The running belt doesn’t keep center ....................20 9.3. Inclination doesn’t work ........................20 9.4. The general electric power switch doesn’t stay on ................20 9.5. Noise from motor ..........................20 9.6. Noise from roller ..........................20 www.cardioline.it...
- Page 5 Further information and clarifications can be requested directly from: ® CARDIOLINE - Supporto Prodotto Via Fratelli Bronzetti, 8 – 20129 Milano (MI) ITALIA e-mail: service@cardioline.it tel. +39 02 94750484 fax: +39 02 94750472...
-
Page 6: Recapitulation Of Machine Marking Data
600 RECAPITULATION OF MACHINE MARKING DATA RECAPITULATION OF MACHINE MARKING DATA In case of necessity or following to the instructions of this manual, please contact Cardioline Spa telling always the following data: Serial number:……….. Year of construction: 20__ Copy of the label on the machine: 1.1. -
Page 7: Other Important Information
Other important information This manual was written with the utmost care. Should you find any details which do not correspond to those contained in this manual, please inform Cardioline SpA who will correct such inconsistencies as soon as possible. The information contained in this manual is subject to change without notice. -
Page 8: How To Use And Keep The Manual
xr 600 HOW TO USE AND KEEP THE MANUAL HOW TO USE AND KEEP THE MANUAL 2.1. Consegnee Keep this manual in safety place near the machine; please read it completely before turning on the machine in order to allow a safety using. It is also a valid instrument for service people because it shows the correct operations to be followed for good maintenance of the medical device. -
Page 9: Important Safety Instructions
xr 600 IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS 3.1. Uncorrect or unforeseen use The treadmill needs to have particular attention to EMC (Electromagnetic Compatibility) and must be installed in conformity to EMC info as follows. Mobile phones can disturb the correct functioning of MD. The treadmill cannot be turned on without or unconnected safety devices (protection covers, emergency stop, etc …) because of electric risks. -
Page 10: Machine Handling
xr 600 IMPORTANT SAFETY INSTRUCTIONS 3.2. Machine handling It can be made by authorized people from producer or client, as per sales agreements. Before any handling, the handlers must carefully read the manual following the instructions written on it. The machine is sold by constructor on wooden pallet to be moved with appropriate fork-lift: gross weight 230 kg with packing and pallet for model range M.D. - Page 11 xr 600 IMPORTANT SAFETY INSTRUCTIONS See 3.7 electric requirement for connection to power supply and 3.10 how to centre the running belt for running belt centring if necessary.
-
Page 12: Safety Parts
xr 600 IMPORTANT SAFETY INSTRUCTIONS The treadmill is equipped with two self-centering for the belt, but if it tends to move to the sides it is necessary to act on the left rear screw (see 3.10 how to centre the running belt). Before connecting the machine to the power supply it must be checked if the power supply characteristics are in accordance with those indicated on the treadmill’s label (See 3.7 electric requirement). -
Page 13: Electric Requirements
xr 600 IMPORTANT SAFETY INSTRUCTIONS the normal level of attention, feeling and reaction. The machine cannot be used without safety parts and devices well mounted or not efficient because they could create electric risks. 3.7. Electric requirements Connect the machine to 220 240 volt electric circuit, frequency 50 60Hz, with plug to hearth of minimum 12 Ampere for range XR600 treadmills. - Page 14 xr 600 IMPORTANT SAFETY INSTRUCTIONS that the belt is too loose and it must be tight; on the contrary if the belt cannot be stopped, it means that the belt is too tight and must be released. For belt tightening or releasing, turn the right and left rear screw with moving of half a turn each time.
-
Page 15: Treadmill Description
Don’t use the machine under the effect of drugs, alcohol or medicine that can reduce the normal level of understanding or reaction. 4.3. Treadmill uses This Medical Device can be used as follows: XR600R XR450R Remote use with S232 4.4. Emergency In case of emergency the red emergency button cuts electricity for motion and motor machine has a decreasing immediate stop. - Page 16 xr 600 IMPORTANT SAFETY INSTRUCTIONS Pushing the red emergency button the treadmill makes one beep per second to report the stop. Rotate clockwise the red stop button / re-install the red magnet in the yellow hole to reset the emergency and unblock motor...
-
Page 17: Software
xr 600 SOFTWARE SOFTWARE After turning on, the treadmill automatically resets itself bringing the inclination to end run. During this operation the oil-can under the motor cover sprays a little quantity of oil under the running belt. The belt runs at low speed for about 10 sec. At the end of the self-lubrication operation, the treadmill stops, brings it to inclination default value (see 5.2 Setup) and makes 3 beeps (2 short and 1 long) meaning that it is ready to be connected to ECG. - Page 18 xr 600 SOFTWARE 5) Click on “TREADMILL Basic Setting” to see and set up the values. Once values are set up, click on “Write Basic Machine Setup” to send to the machine the values just modified. With this software it’s possible to change/set up the following values: ...
-
Page 19: Extraordinary Lubrication
xr 600 SOFTWARE Click on “Update machine software” if you want to update the machine software. 5.3. Extraordinary lubrication Every 250 km (this value can be modified from SetUp, see 5.2), at turning on, the machine will go down 4 times (this value can be modified from SetUp, see 5.2), spraying oil for special belt lubrication. -
Page 20: Technical Description
600 TECHNICAL DESCRIPTION TECHNICAL DESCRIPTION 6.1. Technical specifications XR600R XR450R USES: Remote use SPECIAL CHARACTERISTICS: Forward speed 0.1 – 25.0 km/h 5% Reverse speed 0.1 – 5.0 km/h 5% Speed increment 0.1 km/h Inverter Inverter 2.2 Kw 230V with filter Inverter 1.5 Kw 230V with filter... -
Page 21: Connecting Cable
xr 600 TECHNICAL DESCRIPTION 6.2. Connecting cable 3 mt. length electric power supply earth wire (supplied). 6.3. Accessories Use of accessories not supplied with machine can cause the increase of electromagnetic output and decrease of machine immunity to external electromagnetic sources. -
Page 22: Maintenance Instructions
xr 600 MAINTENANCE INSTRUCTIONS MAINTENANCE INSTRUCTIONS User or person in charge of machine maintenance can only carry out procedures as follows: 7.1. Outer cleaning Clean the machine and the console only with wet cloth. Do not use solvents. Before cleaning make sure the plug is disconnected. -
Page 23: Danger And Emergency
xr 600 MAINTENANCE INSTRUCTIONS 7.7. Danger and emergency ATTENTION! MACHINE UNDER VOLTAGE. DANGER OF CONTACT WITH PARTS UNDER VOLTAGE, SHORT CIRCUIT, BURN. Do not put the plug into socket and do not turn on the machine with plastic motor cover open. Before opening it, turn off the general electric switch and take off the electric plug. -
Page 24: Guarantee
xr 600 GUARANTEE GUARANTEE The constructor guarantees the machine free from material or working defects. Guarantee is valid for 3 years on mechanic, electric or electronic parts starting from date of purchase stated by consignment document issued by producer or retailer. Guarantee means substitution or repairing free of charge of defective parts not including accessories, plastic bodies, belt and all parts showing defects due to negligence, carelessness, bad or correct use, unfit maintenance, not authorized use, bad assembling or installation or maintenance made by personnel not authorized by the constructor. -
Page 25: Problems And Solutions
xr 600 PROBLEMS AND SOLUTIONS PROBLEMS AND SOLUTIONS 9.1. The running belt stops and restarts Control the belt tension (see 3.11 best running belt tension) because if belt is too loose or too much lubricated it could slip. 9.2. The running belt doesn’t keep center The belt is too tight or user hangs on only one side handrail. - Page 26 xr 600 Sales Office: Via F.lli Bronzetti, 8 20129 Milan, Italy T. +39 02 94750470 F. +39 02 94750471 Factory: Via Linz, 151 38121 Trento Italy T. +39 0463 850125 F. +39 0463 850088...
Need help?
Do you have a question about the XR600R and is the answer not in the manual?
Questions and answers