Advertisement
3.
INTRODUCTION
Extremely short collapsed height makes these rams suitable for use where there is almost no clearance at the
lift point. Unique ram and cylinder bearings absorb eccentric load stresses in order to protect the cylinder
against abrasion, over-extension and jamming. Chromed rams with polyurethane seals and wipers provide
longer service life. Rams feature high flow quick connecting couplers with dust caps. Use in conjunction with
10T or 4T pump and hose (610/40, 610/42 or 604/40, 604/42
4.
INSTRUCTIONS FOR USE
WARNING! Ensure you have read and understood chapter 1 safety instructions.
p
p
Note:
These instructions are intended to provide a guide to basic operation and are in no way intended to
replace the advice/instruction of a qualified specialist.
Only fully trained persons should use this equipment.
4.1
Remove plug from ram connector (retain plug to reseal connector after use).
4.2
Connect to suitable hydraulic pump (see section 3).
4.3
Position ram as required and operate pump.
IMPORTANT: Always store the ram with the piston fully retracted to help prevent corrosion. Rams with signs of
rust on the main piston cannot be replaced under warranty.
5.
MAINTENANCE
IMPORTANT: Only fully qualified personnel should attempt maintenance or repair to the hydraulic system.
WARNING: DO NOT use brake fluid, or any fluid other than hydraulic jack fluid, as this may cause
p
p
serious damage to the pump/ram and will invalidate the warranty! Use only Sealey hydraulic oil.
5.2
General
Before each use check for damage to ram, pump, hose and accessories. If any suspect item is found
remove from service and take necessary action to remedy the problem.
Replace/repair with genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Keep all parts of the kit clean - use only a mild detergent and a damp cloth. DO NOT use solvents.
Note: A small amount of oil around ram seal is normal - a thicker layer of oil may be deposited onto the ram
initially, due to the ram seals bedding in.
Hydraulic coupling will weep a small amount of oil, particularly if ram is under pressure when coupling is
released - this is normal.
IMPORTANT: NO RESPONSIBILITY IS ACCEPTED FOR INCORRECT USE OF THE RAM.
Hydraulic products are only repaired by local service agents. We have service/repair agents in all parts of the UK.
DO NOT RETURN RAM TO US. Please telephone us on 01284 757500 to obtain the address and ‘phone number of your local
agent. If product is under guarantee please contact your dealer.
De-commissioning Hydraulic Pump/Ram
Should the ram become completely unserviceable draw off the oil into an approved container and dispose of the product and the oil
according to local regulations.
Declaration of Conformity We, the sole importer into the UK, declare that the product listed below is in
conformity with the following standards and directives.
The construction file for this product is held by the Manufacturer
SHORTY PUSH RAM
and may be inspected, by a national authority, upon request to
MODELS: RE97XS05,
Jack Sealey Ltd.
RE97XS10, RE97XS20,
RE97XS30
Signed by Mark Sweetman
98/37/EC Machinery Directive
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required
for any claim. INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including
postcode.
Sole UK Distributor,
01284 757500
Sealey Group,
Bury St. Edmunds, Suffolk.
For Jack Sealey Ltd.
Sole importer into the UK of
1st November 2004
Sealey Power Products.
01284 703534
sales@sealey.co.uk
www.sealey.co.uk
e-mail
Web
RE97XS05, RE97XS10, RE97XS20, RE97XS30 - 1 - 091104
RE97XS05
1
RE97XS05.01
NUT
2
RE97XS05.02
RAM
3
RE97XS05.03
SEAL WASHER
4
RE97XS05.04
U-CUP SEAL
5
RE97XS05.05
CYLINDER BASE
6
RE97XS05.06
QUICK COUPLER
RE97XS10
1
RE97XS10.01
NUT
2
RE97XS10.02
RAM
3
RE97XS10.03
SEAL WASHER
4
RE97XS10.04
U-CUP SEAL
5
RE97XS10.05
CYLINDER BASE
6
RE97XS10.06
QUICK COUPLER
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required
for any claim. INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
Sole UK Distributor,
01284 757500
Sealey Group,
Bury St. Edmunds, Suffolk.
PARTS FOR:
SHORTY PUSH RAM
Model:
RE97XS05, RE97XS10
RE97XS05, RE97XS10
RE97XS20, RE97XS30
RE97XS20, RE97XS30
RE97XS20
1
RE97XS20.01
NUT
2
RE97XS20.02
RAM
3
RE97XS20.03
SEAL WASHER
4
RE97XS20.04
U-CUP SEAL
5
RE97XS20.05
CYLINDER BASE
6
RE97XS20.06
QUICK COUPLER
RE97XS30
1
RE97XS30.01
NUT
2
RE97XS30.02
RAM
3
RE97XS30.03
SEAL WASHER
4
RE97XS30.04
U-CUP SEAL
5
RE97XS30.05
CYLINDER BASE
6
RE97XS30.06
QUICK COUPLER
01284 703534
www.sealey.co.uk
sales@sealey.co.uk
e-mail
Web
RE97XS05, RE97XS10, RE97XS20, RE97XS30 - 1 - 091104
Advertisement
