Advertisement
Quick Links
www.ecoological.com
Approximate installation time: 30-45 minutes, based on installer
• Center punch
• Drill
Standard AeroBox™, complete with door, (2) keyed cam locks, and load floor
Kit #1: All Assemblies – Wheels
• (2) Wheels
• (2) Axle bolts
• (2) Main door keys
Kit #3B: Standard Assembly – Rubber Feet
• (4) Rubber Feet
• (4) #6-32 X ¾ inch screws for rubber feet
• (4) #6-32 hex nuts and (4) #6 split washer
Kit #3C: Standard Assembly – Hardware
• (2) 5/16-18 x 2 in. thumb screws
• (2) 5/16-18 Nylock™ flanged nuts
• (2) Threaded rivet inserts
• (1) Threaded insert install tool
Read all instructions before installing or using this product. The AeroBox™ will fit most full-size truck beds
that have >58.5 inch tailgate opening, including liner thickness. Please view our helpful installation video and
FAQ's on our website, or call customer service at (844) 918-3688 if you have additional questions. Any
modification or unintended use of this product shall immediately void all manufacturer's warranties. The
manufacturer disclaims all liability for injuries to persons or property resulting from any modifications to,
unintended use, or improper assembly of this product.
1. Place AeroBox™ upside down on clean surface
2. Locate the threaded inserts in the wheel pocket
3. Insert the axle (wheel bolt) through the bearing on the
wheel and thread in to the threaded insert using ½ inch
wrench or socket until tight. Do not overtighten.
4. Repeat for remaining wheel.
1. While in upside down position, drill 9/64 inch hole at the center mark of each foot location
2. Position AeroBox™ with door side up
3. Insert #6 X ¾ inch machine screw through the bumper foot and through drilled hole.
4. Install split washer and nut on to screw by accessing through AeroBox™ door opening
5. Repeat for remaining bumper feet
Note: Rubber feet help keep AeroBox from sliding. In some cases, you may prefer to
leave off rubber feet for easier sliding.
www.ecoological.com
Installation Manual-Standard
©2017 Ecoological
-INSTALLATION TIME-
-TOOLS REQUIRED-
• Phillips screwdriver
• 5/16"-18 x 1.5" bolt and washer
-PARTS INCLUDED-
AEROBOX™ WHEEL INSTALLATION
RUBBER FEET INSTALLATION
©2017 ECOOLOGICAL LLC
10/2017
• 5/16" and 1/2" wrenches or sockets
• 9/64", 3/8", 1/2" drill bits
AB Standard Assembly 10-2017
-
Advertisement
Related Manuals for Ecoological AeroBox
Summary of Contents for Ecoological AeroBox
- Page 1 • (2) Threaded rivet inserts • (1) Threaded insert install tool Read all instructions before installing or using this product. The AeroBox™ will fit most full-size truck beds that have >58.5 inch tailgate opening, including liner thickness. Please view our helpful installation video and FAQ’s on our website, or call customer service at (844) 918-3688 if you have additional questions.
- Page 2 THUMBSCREW ATTACHMENT INSTALLATION 1. Place AeroBox™ in upright position and slide it in to the tailgate opening of your truck until the door of the AeroBox™ would be flush with the tailgate when the tailgate is closed. The AeroBox™ should be centered in the opening.
- Page 3 6. To secure your AeroBox™ in the truck bed, slide it into position, open the door, and insert the thumbscrew fastener through the drilled hole in the floor. Align thumbscrew with the threaded insert and tighten until flanged nut bottoms out on AeroBox.
- Page 4 If you are not completely satisfied with your purchase, you may return a product within 30 days of receiving your order. The product must be in new condition and include original packaging, all parts and paperwork. Ecoological does not accept returns of used products or products returned more than 30 days after delivery.