Performance; Customer Adjustments; Indicators; Terminal Descriptions - PowerTec 2000C Instruction Manual

2.4 PERFORMANCE

MAXIMUM LOAD:
SPEED REGULATION:
SPEED ACCURACY:
Analog Mode:
Linearity:
Digital Mode:
DISPLACEMENT POWER FACTOR:

2.5 CUSTOMER ADJUSTMENTS

ACCELERATION TIME:
DECELERATION TIME:
MAXIMUM SPEED:
JOG SPEED:
CURRENT LIMIT:
GAIN RANGE:
STABILITY:
MINIMUM SPEED:
JUMPERS: JP1
JP2

2.6 INDICATORS

Current Controller board
HS1, HS2, HS3 (encoder)
Low level POWER
OVervoltage/UNdervoltage
Power Loss
Instantaneous Over Current
BUS (charging/ready)
ENABLE

2.7 TERMINAL DESCRIPTIONS

TB1 Current Controller Board (Part # 4001-141108-XXX)
1 Shields and Ground connection
2 HS1 position encoder
3 HS3 position encoder
4 HS2 position encoder
5 HS4 speed encoder
6 HS5 speed encoder
7 Common for encoder ONLY
8 +5VDC for encoder ONLY
9 Common for terminals 10 and 11
10 Auto/Manual Selection +24VDC
11 External Frequency Input +24VDC
12 Collector of FAULT transistor
13 Emitter of FAULT transistor
14 Load output (-2VDC = 150%)
15 Auxiliary Supply output
16 Power Common
TB2 Speed Controller Board (Part # 4001-141107-XXX)
1 RUN contact (closes on RUN)
2 RUN contact 1 Amp 125VAC
3 -24VDC raw supply 50mA max
4 RUN input +24VDC to RUN
5 RUN hold (junction of RUN and STOP)
6 SPARE (tie point for motor thermal)
10
Page
150% for 1 minute out of 10 minutes
0% (no load to full load)
(percentages referred to set speed over 100:1 speed range)
+/- 1.0% (typical with speed pot supplied by internal reference)
+/- 0.5% (typical from external reference source)
0% (+/- 3/4 revolution of motor shaft)
0.96
2 to 30 seconds, linear, analog mode
2 to 30 seconds, linear, analog mode
600 to 5000 RPM, motor dependent
0 to 30% of maximum speed, analog mode only
0 to 150%, resistor calibrated
10 to 1
20 to 1 dynamic range
0 to 15% (with 5K speed pot)
IN: ramp to stop OUT: coast to stop
IN: standard accel and decel
Speed Controller board
RUN
Current Limit
Zero Speed
Base Driver board
Base Drivers (6)
17
TB3
OUT: 50 msec accel and decel
Current Sensor board
UnderVoltage
Undervoltage Time Out
OverVoltage
Heatsink OverTemperature
THerMaL
RELAY ON
7 Emergency STOP +24VDC to RUN
8 +24VDC RUN Logic Supply 50mA max
9 +10VDC reference supply
10 Speed reference input 0 to +10VDC
11 Minimum speed connection for speed pot
12 Signal common
13 Jog input +24VDC to JOG
14 Forward/Reverse input +24VDC to reverse
15 Frequency output open collector to common
16 Zero speed output open collector to common
+24VDC raw supply 50mA max
18 Current reference 0 to +10VDC (velocity error)
Current Sensor Board (Part # 4001-144009-XXX)
1 Trip calibration resistor
2 Trip calibration resistor
3 RTO output
4 Horsepower calibration resistor
5 Horsepower calibration resistor
6 Motor Thermal input
7 Motor Load output (-10VDC = 180%)
8 Common
9 -24VDC
10 Contactor control
Model 2000C / 3000C Manual