Advertisement
Quick Links
BLE V5.0 RS-232 adapter user manual V1.6
1. Package content:
BLE V5.0 RS-232 adapter
White Box: 11 x 6 x 5 (cm)
Total Package Weight: 100 g
2. Profile:
2.1 Top view:
LED:
Link: Blue
PWR/Data: Red
LED Status
Data LED
Data LED solid on
Link LED solid on
Link LED flash
Data & Link LED solid on
Bluetooth V5.0 BLE
Model: S2B5232I (Internal Antenna)
Data transmission
flash
No data transmission
BLE Link
No Link
DFU/OTA Mode
RS-232 Serial Adapter
Package Contents:
BLE V5.0 RS-232 adapter x 1
A4 User manual x 1
Mini USB Cable x 1
DB9 (Male)
Reset to Default
Mini USB (Power)
+
▲ ▲ ▲ ▲
▼ GND
Antenna Inside
(Keep clear area)
Description
1
(5~40 VDC)
2020.08.14
Advertisement
Summary of Contents for Uconnect RS-232
- Page 1 BLE V5.0 RS-232 adapter user manual V1.6 2020.08.14 RS-232 Serial Adapter Bluetooth V5.0 BLE Model: S2B5232I (Internal Antenna) 1. Package content: BLE V5.0 RS-232 adapter Package Contents: BLE V5.0 RS-232 adapter x 1 A4 User manual x 1 ...
- Page 2 BLE V5.0 RS-232 adapter user manual V1.6 2020.08.14 2.2 Rear Side: ▲ DCE ▼ DTE DIP Switch Switch configuration: Setup CTS/RTS Unused Parity Role Baud Rate 3-2-1 0: by APP or 0: Disable 0: None 0: Peripheral 110:2400 Command 1: Enable...
- Page 3 BLE V5.0 RS-232 adapter user manual V1.6 2020.08.14 Signal DTE Direction DCE Direction Description Input Output Transmitted data Output Input Received data Ground Output Input Clear to send Output Input Request to send (Default) Power Input (5~40 VDC) 3. Power supply: 3.1 Voltage: 5~40 VDC,...
- Page 4 BLE V5.0 RS-232 adapter user manual V1.6 2020.08.14 5. GATT Service: 5.1 Architecture: Device Information SetCharacteristicNotification(Char) Firmware Revision String (Char) SetCharacteristicNotification TxData SetCharacteristicNotification(Char) SERIAL RxData writeCharacteristic(Char) BLE_CONF writeCharacteristic(Char) MacID writeCharacteristic(Char) writeCharacteristic(Char) DeviceName writeCharacteristic(Char) PinID_Setting Mobile APP Serial BLE Service 5.2 UUID_1800_SERV = ("00001800-0000-1000-8000-00805F9B34FB") UUID = 2A00, Device name, Default: BLE232 ...
- Page 5 6. Command set via COM port: Command Value Description Check the connection status between control terminal and the RS-232 adapter. Response: “OK” when the connection is ok. Response: “ERROR” when the connection is not ok. BAUD= This command is used to specify the baud rate of COM port.
- Page 6 BLE V5.0 RS-232 adapter user manual V1.6 2020.08.14 DFU= Device Firmware Upgrade via PC software. OTA (Over the air) is available to upgrade the firmware by APP ECHO= This command is used to specify whether the adaptor echoes characters received from the UART back to the DTE/DCE.
- Page 7 BLE V5.0 RS-232 adapter user manual V1.6 2020.08.14 Display the current setting of the adapter VERSION= This command is used to inquiry the firmware version. Inquire the version codes. 7. Central and Peripheral: (Similar like the traditional Bluetooth Master and Slave roles) 7.1 DIP switch setting: The central will pair the slave automatically, please refer to page 2...
- Page 8 BLE V5.0 RS-232 adapter user manual V1.6 2020.08.14 Send data Receive data Download: Please contact the supplier for the APP download or the sample code. Android: iOS:...