Summary of Contents for Vega Absolute VEGA M Series
Page 1
TRACKING DEVICE VEGA M User Manual This manual is designated for tracking devices Vega M: Vega М50 Vega М100 Vega М110...
Page 2
Vega M / User Manual Document Information Title Tracking device VEGA M Document type User Manual – Translation from Russian Document number В-01М100-01 Revision and date 09 – 18.06.2020 This document applies the following products: Product line Product model VEGA M VEGA M100 VEGA M110 VEGA M50...
Vega M / User Manual INTRODUCTION This manual is designated for tracking devices Vega M100, Vega M110 and Vega М110 (hereinafter – the device) manufactured by OOO Vega-Absolute and provides information on powering and activation procedure, control commands and functions of the device.
Vega M / User Manual 1 DESCRIPTION AND OPERATION Vega M100 (Vega M110, Vega M50) off-line tracking device is designed to track a protected object by means of automatically sent messages with the movement and stop points of the object in case unauthorized movement is detected, or should the object leave the specified zone, or by the request of the owner.
Page 6
Vega M / User Manual Figure 1 – Physical form of Vega M100 (top figure), Vega M110 (middle), Vega M50 (bottom figure). Revision № 09 – 18.06.2020...
Vega M / User Manual 2 SPECIFICATION Parameter М100 М110 Housing dimensions, 55x40x20 70х40х20 85х60х22 Housing protection IP54 IP67 class ─ 40…+85 Operational temperatures, °С Off-line operation in the following modes: - «Background» 2 years - «Tracking» 2 weeks The tracking device has the following functions: Parameter setting through SMS-messages and personal page at the website: vega-m.com...
Vega M / User Manual 3 INTENDED USAGE ACTIVATION The activation procedure as follows: STEP 1 Open the cover of the device and insert the micro-SIM-card in the slot. The device shall be powered off at this step. The side of the SIM-card with the beveled corner shall be pointed inward the slot STEP 2 Insert the CR123 batteries into the battery compartment.
Page 9
Vega M / User Manual number from which the message has been received as the owner's phone number. 3. Send an SMS-message with the text 1234*35#+XXXXXXXXXXX* to the SIM-card number of the device, where + XXXXXXXXXXX is the phone number that the device shall remember as the owner's phone number.
Vega M / User Manual STEP 5 After identifying the coordinates, the device registers again in the network and sends an SMS-message with the coordinates of the device. After sending the coordinates, the device switches to standby mode, waiting for SMS-messages with settings or commands from the user.
Page 11
Vega M / User Manual communication sessions (parameter "12", see table 1) the device switches on only for receiving possible SMS-commands and synchronizing with the server. You can obtain the coordinates in the intermediate session by sending an SMS-command with the text "500"...
Page 12
Vega M / User Manual «TRACKING» MODE In the "TRACKING" mode, the device identifies and sends its coordinates in the form of SMS or to the server (depending on the parameter "G", see table 1) every 20 minutes. To activate the "TRACKING" mode, send an SMS-message to the SIM-card number of the device with the text "007"...
Vega M / User Manual PROTECTION METHODS PROTECTION WITH MOTION SENSOR When enabling this function, the device switches on and identifies its coordinates when the object with the sensor starts moving. Parameters "38", "20", "47", "T", "D" and "C" are responsible for the operation of the sensor (see the chapter "Settings").
Page 14
Vega M / User Manual "G", see Table 1). After that the device remains connected for 3 minutes to receive possible SMS-commands and switches to the sleep mode. 3. After this procedure, the device powers off the motion sensor, and does not respond to movements for the time set in parameter "47"...
Page 15
Vega M / User Manual the user does not answer within 30 seconds, the device sends an SMS with a notification. Geofence violation detection is specified by the parameter Z and has four setting options: OPTION 1 Control is OFF. To enable this option, send an SMS-command with the text "XXXX*Z#0*", where XXXX is the device PIN.
Page 16
Vega M / User Manual To enable this option, send an SMS-command with the text «XXXX*Z#3YYY*», where XXXX is the device PIN, and YYY is the diameter of the security zone. If the device receives one of the above-stated commands to enable zone violation control, but is not able to identify the coordinates in the current session, the control does not turn on, and sends the message "Parameter Z is not changed.
Vega M / User Manual SETTINGS This chapter describes the parameters available for changing with SMS-commands. Commands can be sent both from the owner's phone and from another phone (only with the device PIN before the main command). PIN means a four-digit PIN, the default value is 1234.
Page 18
Vega M / User Manual The period for automatic identification of coordinates by satellites (at all other times the coordinates are identified by the GSM base stations) SMS-command: PIN*N#X* Example. Period setting: 6 days: 1234*N#6* Communication frequency (by default - 1) SMS-Command: PIN*12#X* , where X = 1…3 1 –...
Page 19
Vega M / User Manual Operation mode of the motion sensor (by default - 0) SMS-command: PIN*38#X or 38X, where X = 0…3 0 – OFF 1 – continuously ON 2 – ON in time interval 1 3 – ON in time intervals 1 and 2 Example.
Page 20
Vega M / User Manual Example. Messages sent only to the server: 1234*G#2* Security zone violation control (by default - 0 001) SMS-command: PIN*z#X YYY, where Х = 0…3 Y = 1…999 (security zone diameter, km) 0 – security zone violation is not controlled 1 –...
Page 21
Vega M / User Manual The following settings are designated only by the experienced users Setting of the IP-address and server port, where the data from the device are sent SMS-Command: PIN*IP#xxx.xxx.xxx.xxx:yyyyy* Example. IP: 123.123.123.123 and port: 55555 1234*ip#123.123.123.123:55555* Sensor sensitivity per amplitude SMS-Command: PIN*T#xx*, where x=0…40 Example.
Vega M / User Manual PARAMETERS FOR WORK WITH WIALON The device supports data exchange using the WIALON protocol. Table 2 shows the device parameters for working with this protocol. Table 2. Work start by WIALON (by default - OFF) SMS-Command: PIN*w#X* Example.
Vega M / User Manual INDICATION The indication is carried out by one red LED, which flashing depends on the state of the device. The values of the various indication types see Table 3. Table 3. Waiting for an incoming call or Frequent flashings SMS while the device is activated Double flashings every 3...
Vega M / User Manual SMS-COMMANDS The tracking device is controlled, operation modes and protection methods are changed with the SMS-commands. The description of the SMS-commands see Table 4. Table 4. 007 or 666 – from the owner’s phone number XXXX666 or XXXX007 –...
Page 25
Vega M / User Manual 380 - from the owner’s phone number or Motion sensor OFF XXXX380 – from the unknown number 381 - from the owner’s phone number or Protection ON with motion sensor. XXXX381 – – from the Motion sensor continuously works unknown number 382 - from the owner’s...
Vega M / User Manual WORK WITH THE WEBSITE For more efficient and convenient work with the device, register on the web site: vega-m.com and bind your tracking device to your personal page. Also, on the site there is an opportunity to see the location of any one device by clicking the button "Where is the device?"...
Vega M / User Manual CONFIGURATOR You can configure and manage device parameters, as well as update firmware, through the "M100 (M110) Configurator" program. Connection to the device through the Configurator program is carried out automatically when the device is connected to the computer via USB and the Configurator is launched.
Vega M / User Manual 4 TRANSPORTATION AND STORAGE REQUIREMENTS The tracking device shall be stored in its original packaging in heated room at temperatures +5°С to +40°С and relative humidity less than 85%. The tracking device shall be transported in covered freight compartments of all types at any distance at temperatures -40°C to +85°C.
Vega M / User Manual 6 WARRANTY The manufacturer guarantees normal operation of the tracking device for 36 months from the date of sale. The manufacturer undertakes to repair or replace the failed device within 36 months from the date of sale. The consumer undertakes to comply with the terms and conditions of transportation, storage and operation specified in this user manual.
Vega M / User Manual APPENDIX EXAMPLES OF SMS SENT BY THE DEVICE 1 EXAMPLE OF AN SMS-MESSAGE WITH THE DEVICE SETTINGS EXPLANATION 39 1234 the device PIN 1234 35 +79131112233 Owner’s phone number The current operation mode - «Background» A/h 40 % Battery charge - 40 % 58 50...
Page 32
Vega M / User Manual 1000 1700 and 10:00 – 17:00 47 5 Ignoring time of motion sensor After triggering - 5 minutes data transfer: SMS + server Z 1 001 Perimeter control ON, mode 1 Geofence diameter - 1 km. GSM signal level –...
Page 33
Vega M / User Manual 2 EXAMPLE OF AN SMS-MESSAGE WITH ADDITIONAL SETTINGS EXPLANATION T = 10 Motion sensor sensitivity per amplitude =10 D = 10 Motion sensor sensitivity per Continuance =10 C = 1 Double control of motion sensor (protection from false triggering) –...
Page 34
Vega M / User Manual 3 EXAMPLE OF AN SMS-MESSAGE FOR WORK WITH WIALON EXPLANATION WIALON: 1 work with WIALON is ON IP 193.193.165.165:20332 IP address of WIALON server Password 12345 password for access to server via WIALON protocol Revision № 09 – 18.06.2020...
Page 35
Vega M / User Manual EXAMPLE SMS-MESSAGE WITH COORDINATES AND DEVICE STATUS IN THE TEXT FORM EXPLANATION 18.03.16 date and time of identification 06:26:07 of coordinates 55 34` 23,34`` coordinates 082 43` 23,45`` Sat = 1 quantity of the found satellites Ts = 01:15 time for coordinates tracking 40 km/h...