Page 2
Stinger is a Power Brand of AAMP Global its product. If you do not agree, please discontinue use 15500 Lightwave Drive, Suite 202 and contact STINGER.
Hardware Guide M4 X 6 M4 X 10 M4 X 12 M4 X 14 M4 X 18 #10 X 3/8 M5 X 10 NOTE: Depending on the installation, not all screws will be used. Note: The 2 Backstrap (SE-1003) can be used in some applications to add additional support or used in custom installations.
Pre-Assembly M4 X 6 Optional Cable Channel Radio Module Double DIN Applications: Attach the Metal Bracket to the Plastic Dash Mounting Bracket using M4 X 6 screws. Attach metal bracket and plastic dash mounting bracket assembly to the Metal Radio Module using M4 X 6 screws. Bracket M4 X 6 Plastic Dash...
Display Assembly The display can be installed Flat or with a Horizontal Angle towards the driver. For flat mounting, attach the Clamp Assembly (1) to the display using M4 X 14 screws (FIG. A). If a horizontal angle is desired, insert the Angle Plate (2) in between the clamp and display and replace 2 of the M4 X 14 screws with longer M4 X 18 screws on the thicker side of the angle plate (FIG.
Using a Double DIN Dash Kit: Radio chassis mounts to the brackets attached to the kit main frame Display Adjustment & Mounting: 1. Install the dash kit side brackets to the main frame. 2. Making sure to use all 8 screws, loosely attach the radio module & mounting bracket assembly to the side kit brackets (FIG.
Page 9
FIG. E 4. Determine the desired position of the display: a. Display can be vertical or tilted up (FIG. E) b. Display can slide up or down (Page 7) c. Display can be tilted horizontally (Page 7 – FIG. B) M5 X 10 Note: There are multiple mounting holes on the mounting bracket to allow adjusting the...
Using a Double DIN Dash Kit: Radio chassis mounts to the kit brackets in the sub-dash, not to the kit main frame Display Adjustment & Mounting: 1. Use all 8 kit mounting screws to attach the radio module & plastic mounting bracket assembly to the kit brackets at the front most location (not to exceed the front of the kit bracket).
Page 11
FIG. J 4. Attach the display to the mounting bracket assembly by hooking bottom spring hook and then pushing up and hooking top hooks. (FIG. J) 5. Determine the desired position of the display: a. Display can be vertical or tilted up (FIG. K) HOOK BOTTOM b.
Using Factory Radio Brackets: Radio chassis mounts to the factory brackets in the sub-dash Display Adjustment & Mounting: 1. Use all 8 kit mounting screws to attach the radio module & plastic mounting bracket assembly to the factory brackets. (FIG. M) a.
Page 13
FIG. O 4. Attach the display to the mounting bracket assembly by hooking bottom spring hook and then pushing up and hooking top hooks. (FIG. O) 5. Determine the desired position of the display: HOOK BOTTOM a. Display can be vertical or tilted up (FIG. P) FIRST, THEN TOP b.
Using a Single DIN ISO Mountable Dash Kit: Radio chassis mounts separately into the sub-dash Display Adjustment & Mounting: 1. Install the dash kit brackets to the main frame. 2. Making sure to use 4 screws, loosely attach the plastic mounting bracket assembly to the side kit brackets.
Page 15
FIG. T 4. Determine the desired position of the display: a. Display can be vertical or tilted up (FIG. T) b. Display can slide up or down (Page 7) C. Display can be tilted horizontally (Page 7 – FIG. B) M5 X 10 Note:There are multiple mounting holes on the mounting bracket to allow adjusting the mounting depth.
Final Assembly BOOT ASSEMBLY PLASTIC "TAB" HAS TO GO INTO A NOTCH (DISPLAY UNIT NOT SHOWN) If needed, attach the rubber boot to the display clamp assembly by aligning the notch on the top edge as shown, and hook the boot to the clamp at 5 locations.
Wiring and Connections Display Cable Multi Camera Power / Speaker GPS Antenna HDMI Input LVDS Cable USB1 CP/AA 15 Amp Fuse USB2 Radio Antenna TOSLINK AV In/Out - Rear Camera Microphone SiriusXM Tuner The top USB1 must be used for Apple CarPlay and Android Auto.
Page 18
Wiring and Connections 16 Pin Power / Speaker Harness Connect radio power and speaker connections to a vehicle specific harness (sold separately) referencing diagram below. Green/Black ■ Rear Left Speaker - REAR L - White/Black ■ Front Left Speaker - FRONT L - Green ■...
Page 19
Wiring and Connections 24 Pin AV / Rear Camera Harness Audio/Video Inputs & Outputs / Rear Camera Video Input / Resistive Steering Wheel Control Inputs To program SWC, go to SETTINGS > Systems Settings > Installer Settings > Passcode:0052 > Advanced Vehicle Settings >...
Page 20
Wiring and Connections 6 Pin SWI / IR Harness 3.5mm Input for optional Steering Wheel Control Interface (PAC Audio SWI-CP2 is recommended for full compatibility and advanced features. Visit PAC-Audio.com) ORANGE Steering Wheel Control Input External IR input EXTERNAL IR BLACK 4 Pin Microphone / Camera Audio Harness Input for External Microphone (included) used for hands-free calling, Apple CarPlay and Android...
Troubleshooting General SiriusXM Satellite Radio SiriusXM Satellite Radio (cont) Black Screen with Audio Check Antenna Touch the screen anywhere as it may have The radio has detected a fault with the Memory End been turned off. SiriusXM antenna. The antenna cable may be This message will display when the Ensure the display cables on the back of either disconnected or damaged.
Upgrades/Options Navigation SD Card Navigation Ready Add optional iGO Navigation with part number SE-P14. Insert the purchased Front of radio module Micro SD card into the front of the radio module. HEIGH10 and iGO are optimized for ease of use and driving safety.