Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for BEROTEC MOFESSOR
Summary of Contents for BEROTEC MOFESSOR
- Page 1 Manual M O F E S S O R Automatic Chain Lubrication System MOFESSOR BEROTEC GmbH...
- Page 2 Manual revision date 04/2020 contact for support: contact@BEROTEC.de MOFESSOR BEROTEC GmbH P a g e...
-
Page 3: Table Of Contents
4.5 Electrics ....................9 4.6 Commissioning ..................10 5. Operation and Maintenance 5.1 Adjusting the Oil Flow ................11 5.2 Refill ....................... 12 5.3 Check and Maintenance ................ 12 6. Troubleshooting 7. Disposal MOFESSOR BEROTEC GmbH P a g e... -
Page 4: Introduction
This manual has to be respected by the user. Please pay attention to possible restrictions by country-specific law. The chain lubrication system MOFESSOR operates with oil. If the installation is done improperly, an uncontrolled loss of oil can lead to soiling the motorbike or even worse safety issues. -
Page 5: Design And Function
• applicator incl. Hose • self-adhesive nozzle mount • t-connector incl. filler pipe and end cap • filling syringe • chain oil MOFESSOR (250ml) • cable tie package • dispensing valve bracket incl. screws • screwdriver • rain-switch bracket •... -
Page 6: Design
Manual Design 3.3 Function • Turn on ignition LED flashes (self-test) MOFESSOR activated • Start of chain lubrication first oil is dispensed after time interval level 1 = 8 min / level 9 = 1,5 min • Continious and automatic chain lubrication... -
Page 7: Rain / Offroad
60. To guarantee a steady oil application on the chain, the control unit is measuring the outside temperature permanently and adjusts the oil flow automatically. We recommend the use of BEROTEC chain oil, tried and tested with the MOFESSOR. The use of other types of oil is possible. However, so-called “biological oils“... -
Page 8: Installation
For some models special installation manuals exist. See our website for more information: https://berotec.de/produkt/chain-oiler/?lang=en Place of Installation MOFESSOR works gravity based. No part of the system should be mounted close to hot components such as exhaust or engine. Under the passenger seat you may find enough space for the installation. - Page 9 The clamping screw (torque: 0,4NM) of the nozzle mount locks the nozzle position. The surface needs to be degreased properly. Bended surfaces are not suitable for the use of the self-adhesive mounts. The processing temperature is at least 20°C. MOFESSOR BEROTEC GmbH P a g e...
-
Page 10: Oil Tank And Dispensing Valve
The tube connectors can be removed by pushing the black locking edge. Electrics is delivered completely wired and tested. Don’t MOFESSOR connect/disconnect the plugs in energized condition. Steps for the electrical installation: 1. Chose installation place for the control unit 2. -
Page 11: Commissioning
(see chapter 5.2). Push the button of the switch for 4 seconds. The red LED will start flashing. The dispensing valve is now open. Wait until oil starts dripping out of the nozzle. If the oil is very cold, MOFESSOR BEROTEC GmbH P a g e... -
Page 12: Operation And Maintenance
The driver is responsible for a correct amount of oil. We are not liable for damages caused by the oil flow being too low or too high. MOFESSOR BEROTEC GmbH P a g e... -
Page 13: Refill
The oil level of the oil tank should be checked and refilled every 1700 miles (long range tank every 3400 miles). Thus you can avoid the system running dry. MOFESSOR BEROTEC GmbH P a g e | 12... -
Page 14: Troubleshooting
- connection failure work Disposal Nonfunctional systems shouldn’t be disposed as a whole but as individual parts depending on the material. Non-recyclable parts have to be disposed according to their type. MOFESSOR BEROTEC GmbH P a g e | 13... - Page 15 Manual MOFESSOR BEROTEC GmbH P a g e | 14...
- Page 16 Manual MOFESSOR BEROTEC GmbH P a g e | 15...
Need help?
Do you have a question about the MOFESSOR and is the answer not in the manual?
Questions and answers