Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for AEL IR 4400
- Page 1 AEL IR 4400 Therapy Unit User Manual...
-
Page 3: Table Of Contents
CONTENTS Page Introduction Location of Parts Labels Indicators and Controls Caution Statement Operating Instructions Operating the unit 9-17 Care and Maintenance Warnings Testing the RF Battery Specifications Battery Re-charging Warranty Terms and Conditions Address of Manufacturer... -
Page 4: Introduction
INTRODUCTION The AEL IR 4400 is a highly versatile and compact laser therapy device that, under the guidance of a qualified Veterinarian, provides a simple method of treatment, delivering relief from many common pain conditions. Because of its simple design and ease of operation, the AEL IR 4400 Therapy Unit is ideal for use either in a clinic or out in the field. -
Page 5: Location Of Parts
LOCATION OF PARTS OLED Display UP button DOWN button LED laser emission indicator light Identification label Battery cover Danger label Aperture warning label Certification label 10. On/Off switch 11. ENTER button 12. START / STOP button 13. Reset buttons (See following page for diagram showing part & label locations) - Page 6 LOCATION OF PARTS 8. Aperture label 4. LED Laser Emission indicator light 7. Danger Label 1. OLED Display 2. Up button 10. On / Off switch button 11. Enter button 3. Down button 13. Reset buttons 12. Start / Stop button 5.
-
Page 7: Labels
LABELS The AEL IR 4400 comes with the following labels: Certification label – This label states that Laserex certifies that the AEL IR 4400 complies with 21CFR 1040.10 and 1040.11. This label appears on the front of the AEL IR 4400. -
Page 9: Indicators And Controls
Place 2 batteries inside each of the slots at the end of the probe of the unit as per the – and + symbols. Place the battery cover back onto the probe. (When you receive the AEL IR 4400, the batteries will already be in the unit.) -
Page 10: Operating The Unit
2. Attaching the head Attach the selected head by screwing it in a clockwise motion onto the hand piece until it has tightened into place. This is done by placing the head onto the hand piece at the 10 o’clock position by lining up the notch and turning it clockwise to the 12 o’clock position. - Page 11 The PIN is factory set to 9999 by Laserex. The first 9 will appear on the screen. Press ENTER until the second asterisk becomes a 9, then press ENTER again until 9999 appear on the screen. After the 4 asterisk become a 9 the word OK will appear in yellow alongside ENTER on the screen.
- Page 12 Frequency Selection: Frequency (Freq) will be highlighted in blue and Continuous Wave (CW) will appear highlighted in orange. If you wish to use the AEL IR 4400 in CW press ENTER to move to the Interlock setting. To change the frequency from CW to one of 7 programmed Nogier frequencies, press UP (with CW highlighted in blue) once to 73Hz, twice to 146Hz and so on.
- Page 13 Press ENTER and the following screen appears As the AEL IR 4400 is a Class 3B laser, it requires a RF safety interlock. You will receive 2 of these with the unit. These can be placed either on the door or window of your office.
- Page 14 It is now advisable to have the laser ready at the position where the subject is to receive treatment. Press the red START / STOP button and the AEL IR 4400 delivers the requested dosage. An audible beep will be heard and the Laser Emission indicator button on the front of the unit will be flashing in green.
- Page 15 DOWN until SAVE is highlighted in blue. Press ENTER and the following screen appears: Press ENTER when M1 is highlighted. The AEL IR 4400 allows for the storing of 14 settings in memory. When OK is highlighted, press ENTER and it will be stored in memory.
- Page 16 ENTER, an image of the laser safety eyewear will appear, then press the red START / STOP button. In case of emergency, press the 2 restart buttons (see diagram) simultaneously and the AEL IR 4400 will switch off. Changing a Dosage: After completing a treatment and you wish to change the dosage...
- Page 17 Press UP so that PREV is highlighted and then press ENTER. Select Manual input and ENTER the appropriate settings. No Head Attached: If no head is attached to the AEL IR 4400, the following will appear on the screen: Press Enter with OK highlighted. The next screen will indicate the following: The AEL IR 4400 should be switched off and the head re-attached.
- Page 18 At this stage, a beep will be audible. If the AEL IR 4400 is not to be used for an extended period of time, remove the batteries and place the unit in its carrying case.
-
Page 19: Care And Maintenance
CARE AND MAINTENANCE The AEL IR 4400 is a very sturdy device that is supplied with its own carry case. However, like any other electronic product, it requires proper care and handling. We recommend the following: Never try to disassemble the device. -
Page 20: Specifications
AEL IR 4400 SPECIFICATIONS LASER Type Laser Diode Wavelengths Available: 904nm x 3, 635nm x 1 Power: 450mW Pulse Repetition Mode: Continuous Wave and preset Nogier frequencies Battery Type: 4 x AA NiMH rechargeable batteries Battery Life: Approximately 2 hours continuous... -
Page 21: Battery Re-Charging
The AEL IR 4400 comes with an AC Adaptor for battery re-charging. Plug the AC Adaptor into the hole on the side of the Laser AEL IR 4400 to re-charge the batteries. It will take 16 hours to re-charge the batteries from being flat to completely re-charged. -
Page 22: Address Of Manufacturer
Address of Manufacturer: Laserex Technologies Pty Ltd 136 Sturt Street Adelaide SA 5000 Australia Telephone: +61 8 8221 6844 Facsimile: +61 8 8221 6944 Web: www.laser3000.net E-mail: sales@laserex.net... - Page 23 Your Authorised Dealer is:...
Need help?
Do you have a question about the IR 4400 and is the answer not in the manual?
Questions and answers