Summary of Contents for ITW Simco-Ion IQ Easy Speed-T
- Page 1 IQ Easy Speed-T & IQ Easy Hybrid-T Static Neutralizing Bars INSTALLATION AND OPERATING INSTRUCTIONS IQ Easy Speed-T & Hybrid-T 5201223 Rev. J Static Neutralizing Bars...
-
Page 2: Table Of Contents
TABLE OF CONTENTS 1. SAFETY WARNINGS ........................1 2. DESCRIPTION ..........................3 3. SPECIFICATIONS ...........................4 4. INSTALLATION ..........................5 Unpacking ..........................5 Mechanical Installation ......................6 Electrical Connections ......................8 For Connection to IQ Power Control Station ................8 Standalone ...........................10 Set Up ..........................11 5. OPERATION ..........................14 Indicator Lights ........................14 With IQ Power Control Station ...................14 Standalone Operation ......................14... -
Page 3: Safety Warnings
1. SAFETY WARNINGS PLEASE READ INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION ALL INSTALLATION AND TROUBLESHOOTING OPERATIONS MUST BE PERFORMED BY QUALIFIED TECHNICAL PERSONNEL The following safety guidelines must be observed in order to prevent physical injury and damage to objects or to the static neutralizing bar itself: This instruction manual uses symbols to identify dangerous situations as follows: WARNING –... - Page 4 CAUTION – The emitters are sharp and can cause physical injury. ATTENTION – Les émetteurs sont pointues et peuvent causer des blessures. NOTE – The high-voltage emitters (9 kV) are limited to a current of 50 uA, which means that they are electrically safe to touch and shockproof. NOTE –...
-
Page 5: Description
2. DESCRIPTION The IQ Easy Speed-T and the IQ Easy Hybrid-T are static bars designed to neutralize electrostatically charged surfaces. Both static bars are equipped with an integrated high-voltage power unit, ion emitters and status LEDs. They require a 24 VDC supply voltage to be provided via a 5-pin M12 connector. -
Page 6: Specifications
3. SPECIFICATIONS Electrical Input Voltage 24 VDC Input Current 0.75A (max) Input Connection 5-pin M12 (A-coded) male receptacle Output Voltage 7.5 kV Speed-T, 9 kV Hybrid-T Output Current (to Ground) 50 μA per emitter (max) Green (steady) = Operation Green (flashing) = Standby Indicators (2) Green (flickering) = Communication Red (steady) = Fault... -
Page 7: Installation
4. INSTALLATION WARNING – Electrical installation and repairs must be performed by a skilled electrical engineer according to the applicable national and local regulations. AVERTISSEMENT – L'installation et le service électrique doivent être effectuées par un électricien qualifié conformément aux réglementations locales et nationales. -
Page 8: Mechanical Installation
Mechanical Installation NOTE – Conductive machine parts in the vicinity of the static neutralizing bar have a detrimental influence on its operation. For optimum results, the static bar must be installed as per Figure 4. 1. Directly in front of where static electricity causes problems. 2. - Page 9 Figure 3: IQ Easy Static Bar Mounting Figure 4: IQ Easy Static Bar Positioning 4. Attach the static neutralizing bar using the fasteners supplied. See Figures 3 and 5. Lock the static bar in the brackets by manually tightening the screws in the brackets.
-
Page 10: Electrical Connections
Electrical Connections WARNING – Electrical installation must be performed by a skilled electrical engineer according to applicable national and local regulations. AVERTISSEMENT – L'installation et le service électrique doivent être effectuées par un électricien qualifié conformément aux réglementations locales et nationales. WARNING –... - Page 11 Figure 5: Typical IQ Easy Cables IQ Easy Speed-T & Hybrid-T 5201223 Rev. J Static Neutralizing Bars...
-
Page 12: Standalone
Standalone The IQ Easy Static Neutralizing Bar may be operated without a control station. In this case, the IQ Easy Static Bar will enter Standalone operating mode. In Standalone Mode, the IQ Easy Static Bar operates in Fixed mode ionization with the standard 50/50 balance. -
Page 13: Set Up
WARNING – For personal protection, and to ensure proper function, the GRAY* and BLUE wires must both be connected to ground. AVERTISSEMENT – Pour votre sécurité, et pour assurer un bon fonctionement, les cables GRIS* et BLEU doivent tous deux être connectés à... - Page 14 Ion Output: Displays the ionization level, in percent, where Bar Calibration = 100% and the ionization level in terms of microamps for both positive and negative ionization. Balance: A ratio of input power supplied to the high voltage power supplies that related to ion balance.
- Page 15 Web Speed: A user entered value used in the Auto-Tune Mode only. Sensor Quantity – The number of sensors found on the sensor bar. Overall Sensor Avg – The average voltage reported by all sensor modules on a static sensor bar. Feedback Sensor Avg –...
-
Page 16: Operation
5. OPERATION The IQ Easy Static Neutralizing Bar performs a self-test which includes illumination of the two (green and red) indication lights on the static bar. The self-test and power up of the high voltage supplies occurs before ionization is produced at the emitters. This takes approximately five seconds after the application of power. -
Page 17: Maintenance
6. MAINTENANCE WARNING – Remove power before working on IQ Easy Bars. AVERTISSEMENT – Débranchez l'alimentation électrique avant toute intervention sur l'appareil. Regular Cleaning Clean the emitter points and the static neutralizing bar regularly with a stiff bristle, non-metallic brush. WARNING –... -
Page 18: Troubleshooting
7. TROUBLESHOOTING WARNING – Remove power before working on IQ Easy Static Neutralizing Bars. AVERTISSEMENT – Débranchez l'alimentation électrique avant toute intervention sur l'appareil. Signal Problem Cause Solution LEDs on bar do No high voltage No supply Apply power to Control Station & not light at emitters voltage... -
Page 19: Parts And Accessories
8. PARTS AND ACCESSORIES Item Part Number Mounting Kit 5051777 M12 to M12 Cables for connecting Static Bar to Control Station with straight connector at bar end 1.5 meter (4.9 foot) 5051939 5 meter (16.4 foot) 5051791 10 meter (32.8 foot) 5051792 20 meter (65.6 foot) 5051793... -
Page 20: Warranty And Service
9. WARRANTY AND SERVICE This product has been carefully tested at the factory and is warranted to be free from any defects in materials or workmanship. Simco-Ion will, under this warranty, repair or replace any equipment that proves, upon our examination, to have become defective within one year from the date of purchase.
Need help?
Do you have a question about the Simco-Ion IQ Easy Speed-T and is the answer not in the manual?
Questions and answers