Table of Contents
Advertisement
Quick Links
®
The CLAMPEX
clamping set is a frictionally engaged, detachable shaft-hub-connection for cylindrical
shafts and bores without feather key.
Table of contents
1
2
2.1
2.2
2.3
2.4
3
3.1
3.2
4
4.1
4.2
4.3
5
6
7
EU directive 2014/34/EU
Please observe protection
note ISO 16016.
CLAMPEX
Operating/Assembly instructions
CLAMPEX
hazardous locations according to
Drawn:
2016-09-09 Shg/Jh
Verified:
2016-09-09 Shg
®
KTR 250
®
KTR 250
®
KTR 250
Replacing:
Replaced by:
KTR-N
40817 EN
Sheet:
1 of 7
Edition:
6
KTR-N dated 2011-05-23
2
3
3
3
3
4
4
4
4
5
5
5
6
7
7
7
Advertisement
Table of Contents
Related Manuals for KTR-Group CLAMPEX KTR 250
Summary of Contents for KTR-Group CLAMPEX KTR 250
- Page 1 KTR-N 40817 EN ® CLAMPEX KTR 250 Sheet: 1 of 7 Operating/Assembly instructions Edition: ® CLAMPEX KTR 250 ® The CLAMPEX clamping set is a frictionally engaged, detachable shaft-hub-connection for cylindrical shafts and bores without feather key. Table of contents Technical data Advice General advice...
- Page 2 KTR-N 40817 EN ® CLAMPEX KTR 250 Sheet: 2 of 7 Operating/Assembly instructions Edition: Technical data 1) Dimension D : For calculation of hub see catalogue "Drive Technology". 2) These are the maximum screw tightening torques. They can be reduced by a maximum of 40 % of the figures specified, with T, F...
- Page 3 KTR-N 40817 EN ® CLAMPEX KTR 250 Sheet: 3 of 7 Operating/Assembly instructions Edition: Technical data Tolerances, surfaces 1) One proper turning process is sufficient (Rz ≤ 16 µm). 2) Highest permissible ® tolerance of hub or shaft. Illustration 2:Tolerances and surfaces (example: CLAMPEX KTR 250) Advice 2.1 General advice...
- Page 4 KTR-N 40817 EN ® CLAMPEX KTR 250 Sheet: 4 of 7 Operating/Assembly instructions Edition: Advice 2.4 Intended use You may only assemble and disassemble the clamping set if you • have carefully read through the operating/assembly instructions and understood them •...
- Page 5 KTR-N 40817 EN ® CLAMPEX KTR 250 Sheet: 5 of 7 Operating/Assembly instructions Edition: Assembly Generally the clamping set is supplied in mounted condition. Before assembly the clamping set has to be inspected for completeness. ® 4.1 Components of clamping set CLAMPEX KTR 250 Component Quantity...
- Page 6 KTR-N 40817 EN ® CLAMPEX KTR 250 Sheet: 6 of 7 Operating/Assembly instructions Edition: Assembly 4.2 Assembly of the clamping set 3. Release the clamping screws slightly. To facilitate the assembly fasten the internal and external ring by two clamping screws each via the pull-off threads (see illustration 5). Insert the clamping set KTR 250 between shaft and hub.
- Page 7 KTR-N 40817 EN ® CLAMPEX KTR 250 Sheet: 7 of 7 Operating/Assembly instructions Edition: Disposal In respect of environmental protection we would ask you to dispose of the packaging or products on termination of their service life in accordance with the legal regulations and standards that apply, respectively. All clamping sets consist of metal.
Need help?
Do you have a question about the CLAMPEX KTR 250 and is the answer not in the manual?
Questions and answers