Table of Contents
Advertisement
Quick Links
1
APPLIANCE ....................................................................................... 4
2
DESCRIPTION ................................................................................... 4
3
PACKAGE CONTENT LIST .............................................................. 5
4
SYMBOLS .......................................................................................... 5
5
SAFETY.............................................................................................. 5
6
KICKBACK SAFETY PRECAUTIONS .............................................. 7
7
SAFETY WARNINGS GASOLINE .................................................... 8
8
ASSEMBLY ........................................................................................ 8
8.1
Tools for assembly ................................................................................................... 8
8.2
Assembly requirements ............................................................................................ 8
8.3
Guide bar / saw chain / clutch cover installation .................................................... 8
8.3.1
Mounting the bucking spike (13) .................................................................................. 8
8.3.2
Installation of the guide bar: ........................................................................................ 9
8.3.3
To install saw chain: .................................................................................................... 9
8.3.4
Saw chain tension adjustment ..................................................................................... 9
8.3.5
To adjust saw chain: ................................................................................................. 10
8.3.6
Chain brake mechanical test ..................................................................................... 10
8.3.7
To test chain brake: ................................................................................................... 10
9
FUEL AND LUBRICATION.............................................................. 11
9.1
Fuel .......................................................................................................................... 11
9.2
Mixing fuel ............................................................................................................... 11
9.2.1
Fuel and lubrication symbols ..................................................................................... 11
9.2.2
Fuel mixing table ....................................................................................................... 11
9.2.3
Recommended fuels ................................................................................................. 11
9.2.4
Filling with fuel .......................................................................................................... 11
9.3
Chain oil ................................................................................................................... 12
9.3.1
Chain and bar lubrication .......................................................................................... 12
9.3.2
Filling with chain oil ................................................................................................... 12
10
OPERATION .................................................................................... 12
10.1
Engine pre start checks (Fig. 8) ............................................................................. 12
Copyright © 2016 VARO
POWXG1022
P a g e
| 1
EN
www.varo.com
Advertisement
Table of Contents
Summary of Contents for Gardenpro POWERPLUS POWXG1022
-
Page 1: Table Of Contents
POWXG1022 APPLIANCE ..................4 DESCRIPTION ................... 4 PACKAGE CONTENT LIST .............. 5 SYMBOLS ..................5 SAFETY....................5 KICKBACK SAFETY PRECAUTIONS ..........7 SAFETY WARNINGS GASOLINE ............ 8 ASSEMBLY ..................8 Tools for assembly ....................8 Assembly requirements .................... 8 Guide bar / saw chain / clutch cover installation ............ 8 8.3.1 Mounting the bucking spike (13) .................. - Page 2 POWXG1022 10.2 To start engine ......................12 10.3 Re-starting a warm engine..................13 10.4 To stop engine (Fig. 9f) ................... 13 10.5 Chain brake operational test .................. 13 10.6 Saw chain / bar lubrication ..................13 10.7 Automatic oiler ......................14 10.8 General cutting instructions ...................
- Page 3 POWXG1022 ENVIRONMENT ................25 DECLARATION OF CONFORMITY ..........25 Copyright © 2016 VARO www.varo.com P a g e...
-
Page 4: Appliance
POWXG1022 CHAINSAW 45 CC – 450 MM POWXG1022 1 APPLIANCE These models are intended for infrequent use by homeowners, cottagers, and campers, and for such general applications as clearing, pruning, cutting firewood, etc. They are not intended for prolonged use. If the intended use involves prolonged periods of operation, this may cause circulatory problems in the user’s hands due to vibration. -
Page 5: Package Content List
POWXG1022 WARNING! When using gas tools, basic safety precautions, including the following, should always be followed to reduce the risk of serious personal injury and/or damage to the unit. 3 PACKAGE CONTENT LIST Remove all packaging materials. Remove remaining packing and package inserts (if included). ... - Page 6 POWXG1022 Use safety footwear, snug-fitting clothing, protective gloves, and eye, hearing and head protection devices. Use caution when handling fuel. To avoid fire, move the chain saw at least 10 feet (3m) from the fuelling point before starting the engine. ...
-
Page 7: Kickback Safety Precautions
POWXG1022 6 KICKBACK SAFETY PRECAUTIONS KICKBACK may occur when the NOSE or TIP of the guide bar touches an object, or when wood closes in and pinches the saw chain in the cut. Tip contact in some cases may cause a lightning-fast reverse reaction, kicking the guide bar up and back toward the operator. -
Page 8: Safety Warnings Gasoline
POWXG1022 7 SAFETY WARNINGS GASOLINE WARNING: Use extra care in handling fuels. They are flammable and the vapours are explosive. The following points must be observed: Use only an approved container. Never remove the fuel cap or add fuel with the power source running. Allow engine exhaust components to cool before refuelling. -
Page 9: Installation Of The Guide Bar
POWXG1022 8.3.2 Installation of the guide bar: To ensure the bar and chain receive oil, only use the original style bar with the oil passage hole (A) as illustrated above (Fig. 3a). Make sure the chain brake lever is pulled back into the disengaged position (Fig. 3b). ... -
Page 10: To Adjust Saw Chain
POWXG1022 8.3.5 To adjust saw chain: Loosen the bar retaining nuts so they are finger tight. Hold nose of guide bar up and turn adjustment screw (A) clockwise to increase chain tension. Turning screw counterclockwise will decrease amount of tension on chain. Ensure the chain fits snugly all the way around the guide bar (Fig. -
Page 11: Fuel And Lubrication
POWXG1022 9 FUEL AND LUBRICATION Fuel Use regular grade unleaded gasoline mixed with 40:1 custom 2-cycle engine oil for best results. Use mixing ratios in section fuel mixing table below. Warning: never use straight gasoline in your unit. This will cause permanent engine damage and void the manufacturer’s warranty for that product. -
Page 12: Chain Oil
POWXG1022 When finished refuelling, immediately refit the cap to the fuel tank, and close by turning it clockwise until hand tight and sealed. Warning: Move at least 3 m from the fuelling spot, away from potential spillage and escaped fumes, before attempting to start the engine. Chain oil 9.3.1 Chain and bar lubrication... -
Page 13: Re-Starting A Warm Engine
POWXG1022 Let the engine run for 10 seconds to warm up. Press the trigger (H) and put it into idle (Fig. 9e). If the engine does not start up, repeat the above steps. 10.3 Re-starting a warm engine Make sure the on/off switch is in the “I”... -
Page 14: Automatic Oiler
POWXG1022 Note: saw chain stretches during use, particularly when it is new, and it will occasionally be necessary to adjust and tighten it. New chain will require adjustment after about 5 minutes of operation. 10.7 Automatic oiler Your chain saw is equipped with an automatic clutch driven oiler system. The oiler automatically delivers the proper amount of oil to the bar and chain. -
Page 15: Limbing
POWXG1022 WARNING: Never walk in front of a tree that has been notched. Make the felling cut (D) from the other side of the tree and 1.5 - 2.0 inches (3-5 cm) above the edge of the notch (C) (Fig. 11b) Never saw completely through the trunk. -
Page 16: Bucking Using A Sawhorse
POWXG1022 Log supported on both ends: First, overbuck 1/3 diameter of log to avoid splintering. Second, underbuck to meet first cut and avoid pinching (Fig. 13c). NOTE: The best way to hold a log while bucking is to use a sawhorse. When this is not possible, the log should be raised and supported by the limb stumps or by using supporting logs. -
Page 17: Winter Maintenance
POWXG1022 11.2 Winter maintenance Your chain saw requires a winter maintenance. Please contact your local dealer for this. It includes the following: Replacing spark plug Sharpening the chain Cleaning of air filter (Replacement if necessary) Cleaning of guide bar Oil pump check up Thorough cleanup Fine tuning and testing 11.3... -
Page 18: Spark Arrester Screen
POWXG1022 11.5 Spark arrester screen Note: a clogged spark arrester screen will dramatically reduce engine performance. Remove the 2 bolts (A) and pull muffler out (Fig. 17a). Remove the 2 screws that holds the cover (B) (Fig. 17b). ... -
Page 19: Sprocket Tip Lubrication
POWXG1022 12.2 Sprocket tip lubrication Caution: the sprocket tip on your new saw has been pre-lubricated at the factory. Failure to lubricate the guide bar sprocket tip as explained below will result in poor performance and seizure, voiding the manufacturer’s warranty. -
Page 20: Guide Bar
POWXG1022 To sharpen the saw chain, use the suitable sharpening tools: round chain file file leading chain measuring calibre. These tools can be bought in any specialized stores. To gain well shaped sawdust particles, use sharp chain. If there appears wooden powder, you must sharpen the saw chain. -
Page 21: Chain Maintenance
POWXG1022 Oil passages - oil passages on the bar should be cleaned to ensure proper lubrication of the bar and chain during operation. Note: the condition of the oil passages can be easily checked. If the passages are clear, the chain will automatically give off a spray of oil within seconds of starting the saw.your saw is equipped with an automatic oiler system. -
Page 22: Technical Data
POWXG1022 13 TECHNICAL DATA Cylinder capacity 45 cc Rotation speed 10.000 min Chain speed 22 m/s Carburettor type Walbro Spark plug type Champion Chain type Oregon Cutting length 450 mm Engine power 1.8 kW Guide bar type Oregon CDI ignition Controlled oil delivery Crank engine Full... -
Page 23: Storing A Chain Saw
POWXG1022 15 STORING A CHAIN SAW Caution: never store a chain saw for longer than 30 days without performing the following procedures. Storing a chain saw for longer than 30 days requires storage maintenance. Unless the storage instructions are followed, fuel remaining in the carburettor will evaporate, leaving gum-like deposits. -
Page 24: Warranty
POWXG1022 PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Have carburettor adjusted Incorrect carburettor mixture authorized service centre. adjustment setting. No power under Drain gas tank (see storage)/add fresh Old or improperly mixed fuel. load. fuel mixture. Air filter is plugged. Replace or clean the air filter. Fouled spark plug. - Page 25 POWXG1022 18 ENVIRONMENT Should your machine need replacement after extended use, do not put it in the domestic waste but dispose of it in an environmentally safe way. 19 DECLARATION OF CONFORMITY VARO N.V. - Joseph Van Instraat 9 - BE2500 Lier - BELGIUM, declares that, CHAINSAW 45 cc –...