Ultratech UT-WD135 User Manual

EN
What You Should Know Before Installation
1.The transmitter(s) supplied with this kit is(are) paired with
receiver(s) and set to default tune "Dingdong",IF NOT, please refer to
the "Getting Started" to pair the transmitter(s) with receiver(s) and set
your favorite tune(s).
2.Metal, walls, ceilings and other RF signals from electronic devices
can affect the radio signal of the wireless doorbell. Generally the
operating range can reach up to 600 feet in the open air and non-
interference environment, and 100~300 feet within obstructive
l
environments.
3.It is not advisable to mount the transmitter onto metal surfaces as
the material can block RF signals between the transmitter and the
receiver. However, if this is the only option then we recommend that
you use the sticky pad provided as opposed to using the provided
screws.
4.The battery using in transmitter is 23A,Operating range will
decrease if battery in transmitter is in low power status.
5.The push button is not advisable to mount the transmitter in the
outdoor directly without any shelter which could accelerate aging of
plastic materials.
e In China ou Should Know Before Installation
ansmitter(s) supplied with this kit is(are) paired with
(s) and set to default tune "Dingdong",IF NOT, please refer to
ting Started" to pair the transmitter(s) with receiver(s) and set
orite tune(s).
walls, ceilings and other RF signals from electronic devices
ct the radio signal of the wireless doorbell. Generally the
g range can reach up to 600 feet in the open air and non-
nce environment, and 100~300 feet within obstructive
ments.
t advisable to mount the transmitter onto metal surfaces as
rial can block RF signals between the transmitter and the
However, if this is the only option then we recommend that
the sticky pad provided as opposed to using the provided
ttery using in transmitter is 23A,Operating range will
4. Reset: Press
e if battery in transmitter is in low power status.
successful when you hear the default doorbell sound with flashing
nd a
LED.
sh button is not advisable to mount the transmitter in the
directly without any shelter which could accelerate aging of
materials.
ver the
Getting Started
tallation
ocation of
(are) paired with
g",IF NOT, please refer to
(s) with receiver(s) and set 5s
n bolts
4
over and
s from electronic devices
orbell. Generally the
5.Transmitter battery replacement: Remove the front of the case by
the open air and non-
t within obstructive
pushing in the tab on the transmitter button with a small screwdriver,
take our the battery and replace with a new one,finally put back in
5
r onto metal surfaces as place.(Battery Model:23A)
he transmitter and the
hen we recommend that
to using the provided
Plug-in Chime
: Press button for 5s to reset the receivers, the reset is
ul when you hear the default doorbell sound with flashing
Back button
erating range will 1
ower status.
2 Forward button
the transmitter in the
Volume control
3
ould accelerate aging of
Plug(US/UK/EU/AU optional)
4
5 Speaker
Push button
6
s
Wireless Doorbell
User Manual
Mounting with screw/anchors:
Please prepare an electric drill, a Phillips-head screwdriver and a
small flat-bladed screwdriver before installation.
(1).Insert a flat-bladed screwdriver into the slot A, carefully lever the
cover and base apart.
(2).Attach the back cover to wall and make two marks at the location of
Getting Started
the two mounting holes.
(3).Drill two holes on the marked locations, insert 2 expansion bolts
provided in the package if necessary. Finally, screw up back cover and
put back the front case.
4
5
Plug-in Chime
Back button
button for 5s to reset the receivers, the reset is 1
Forward button
2
Volume control
3
Plug(US/UK/EU/AU optional)
4
Speaker
5
6 Push button
3
1
2
6
Push Button
Troubleshooting
+
1.The receiver doesn't sound
Check the doorbell button battery, replace it if necessary.
- 
The plug of receiver is loose.

The receiver could be out of range of the doorbell button.

The receiver may not have paired with the doorbell button.

Check that the volume control is not at the minimum setting.

2.Operating range is reduced
Metal structures, including uPVC door frames can reduce the

EN
What You Should Know Before Installation
1.The transmitter(s) supplied with this kit is(are) paired with
receiver(s) and set to default tune "Dingdong",IF NOT, please refer to
the "Getting Started" to pair the transmitter(s) with receiver(s) and set
your favorite tune(s).
2.Metal, walls, ceilings and other RF signals from electronic devices
can affect the radio signal of the wireless doorbell. Generally the
operating range can reach up to 600 feet in the open air and non-
Getting Started
interference environment, and 100~300 feet within obstructive
environments.
3.It is not advisable to mount the transmitter onto metal surfaces as
the material can block RF signals between the transmitter and the
receiver. However, if this is the only option then we recommend that
you use the sticky pad provided as opposed to using the provided
screws.
4 4.The battery using in transmitter is 23A,Operating range will
decrease if battery in transmitter is in low power status.
5.The push button is not advisable to mount the transmitter in the
outdoor directly without any shelter which could accelerate aging of
plastic materials.
5
Made In China
Plug-in Chime
Back button
1
Forward button
2
Volume control
3
4. Reset: Press
successful when you hear the default doorbell sound with flashing
LED.
Plug(US/UK/EU/AU optional)
4
Speaker
5
Push button
6
1.Tune setting or pairing a (an additional)transmitter to receiver :
5s
(1)Press
receiver playing is the tune selected.
5.Transmitter battery replacement: Remove the front of the case by
pushing in the tab on the transmitter button with a small screwdriver,
(2) Hold the
take our the battery and replace with a new one,finally put back in
3
heard and the LED indicator starts flashing.
place.(Battery Model:23A)
(3) Press the transmitter button to send a signal to receiver to confirm,
1
when the tune setting (pairing) is successful, the receiver will play the
2 selected tune automatically.
6
Push Button
Troubleshooting
1.The receiver doesn't sound
Check the doorbell button battery, replace it if necessary.

The plug of receiver is loose.

The receiver could be out of range of the doorbell button.

1.Tune setting or pairing a (an additional)transmitter to receiver :
The receiver may not have paired with the doorbell button.

(1)Press button or Button to choose your favorite tune, the
Check that the volume control is not at the minimum setting.

receiver playing is the tune selected.
(2) Hold the button for about 5s and release until a Ding-dong is
2.Operating range is reduced
heard and the LED indicator starts flashing.
Metal structures, including uPVC door frames can reduce the

(3) Press the transmitter button to send a signal to receiver to confirm,
range of the doorbell. Avoid mounting the transmitter or receiver
when the tune setting (pairing) is successful, the receiver will play the
selected tune automatically.
on or near metal structures.
Other equipment can cause radio interference that affects your

doorbell.
Walls and ceilings will reduce the range.

Weak batteries will reduce range. Replace every 12–18 months.

Features
5s

Choose tune Activate pairing mode





3
1
2
6
Push Button
button for 5s to reset the receivers, the reset is
button or Button to choose your favorite tune, the
button for about 5s and release until a Ding-dong is
+
-
5s
Choose tune Activate pairing mode
Important:
(1)The steps of changing a new tune or pairing an additional
transmitter are the same.
(2)Pairing mode will last for 5s only and quit automatically after
pairing is completed.
(3)The pairing mode is only available for a transmitter each time. For
two or more transmitters, please follow the steps (1)-(3) above
once again to get transmitters paired one by one.
(4)Maximally one receiver can pair with up to 50 transmitters, and the
tune can be set different for each transmitter
2.Volume control: press button on the receiver, this switch
toggles between High and Low volume.
Modern and stylish design
Confirm
52 different selectable tunes
Volume range:25~110dB
4-level adjustable volume
600 feet operation range (in the open air)
Easy to install and use
Easy to add additional transmitters or receivers
Getting Started
3
4
1
1.Tune setting or p
2
6
5
(1)Press button o
receiver playing is th
Plug-in Chime Push But
(2) Hold the butto
heard and the LED in
Back button
1
Forward button
2
(3) Press the transm
3 Volume control when the tune settin
selected tune autom
Plug(US/UK/EU/AU optional)
4
Speaker
5
Push button
6
Choose tune
Troubleshooting
1.The receiver doesn't sound
Check the doorbell button battery, replace it if nec

The plug of receiver is loose.

The receiver could be out of range of the doorbell

The receiver may not have paired with the doorbel

Check that the volume control is not at the minimu

Important:
(1)The steps of changing
2.Operating range is reduced
transmitter are the same.
Metal structures, including uPVC door frames can
 5
(2)Pairing mode will last fo
range of the doorbell. Avoid mounting the transmit
pairing is completed.
on or near metal structures.
(3)The pairing mode is onl
Other equipment can cause radio interference tha

two or more transmitters
doorbell.
once again to get transmit
Walls and ceilings will reduce the range.

(4)Maximally one receiver
Weak batteries will reduce range. Replace every 1

tune can be set different
2.Volume control: press
toggles between High and
Features
Confirm

Modern and styl
Volume range:25~110dB
 52 different sele
 4-level adjustab
3.Mount

600 feet operatio Import
make s
transm

Easy to install an
Mount u

Easy to add add
provide

Low power cons
Mountin
(1).To en
intended
(2).Rem
the unde
transmit
Specifications
Working voltage of plug-in rece
Battery in transmitter:
Note: ple
adhesion
Power consumption of transmitt
the adhe
Wireless range: