Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Diamond DFN175/33A
- Page 1 04/2012 Mod: DFN175/33A Production code: FI 1750/33-(NOMEX)
-
Page 2: Table Of Contents
E031002C 10/04/09 SOMMARIO INTRODUCTION ........................... 3 SAFETY RULES..........................3 MANUFACTURARE LIABILITY..................... 5 TRANSPORT AND UNPACKING ....................6 MACHINE IDENTIFICATION......................7 INSTALLATION PREMISES AND POSITIONING ................ 7 NOISE............................8 EXHAUST (only Gas heated ironers) AND HUMID AIR CONDUCTION........8 ELECTRIC CONNECTION......................8 GAS CONNECTION (only gas heated ironers) ................ -
Page 3: Introduction
E031002C 10/04/09 INTRODUCTION This manual refer to the installation, use and maintenance of industrial drying ironers. This document is written in compliance with EU Directives. The following information are addressed to installer and user, who must be sure to understand them deeply before to work with the ironer. This manual must be always available to be consulted. - Page 4 E031002C 10/04/09 CRUSHING DANGER Introducing the linen in the ironer, the hand must not go under hand safe protection. The linen must be smoothed on the introducing table, where wrinkles and folds must be flatted, then it must be driven on the introduction belts, which will bring it between the roller and the ironing belts. It is forbidden to iron folded linen or more fabrics one up the other.
-
Page 5: Manufacturare Liability
E031002C 10/04/09 ELECTROCUTION DANGER Any operation on the electric pats must be operated only by qualified technician and only after any supply, especially electric, to the machine has been cut. Power and control circuit my be modified only by manufacturer technician, on the contrary the warranty condition will automatically expire. -
Page 6: Transport And Unpacking
E031002C 10/04/09 TRANSPORT AND UNPACKING Please control the machine at the receipt moment and signal to the forwarder any damaged due to the transport both on the external structure and the internal parts. The machine must be moved only using a forklift truck introducing the forks only and exclusively in the apposite room. -
Page 7: Machine Identification
E031002C 10/04/09 The packing material must not be spread on the environment, but must be collect in the appropriate collecting place in compliance with the country rules in force. Remove the transport clamps following with care the instruction inside the machine side. -
Page 8: Noise
E031002C 10/04/09 NOISE The air noise produced by the ironer causes an continue and weighted A level acoustic pressure which is lower then 70 dB. EXHAUST (only Gas heated ironers) AND HUMID AIR CONDUCTION The exhaust conduction (for gas heated ironer) must comply with the rule on matter in force. In case of gas heated ironer the chimney must be adequately far from easily inflammable or combustible materials (at least 500 mm). -
Page 9: Gas Connection (Only Gas Heated Ironers)
E031002C 10/04/09 Take off the door paying attention that already connected cables are not pulled out. Pass the cable through the cable holder on the ironer left side. Electric supply must be done connecting the cable to the terminals mounted on the ironer: Ξ: ground L1, L2, L3: phase N: neutral... -
Page 10: Proof (Only For Gas Heated Ironer)
E031002C 10/04/09 1500 Code Gas kind Pressure at noozle Noozle Air intake position 2E e 2H pos. C: 20 mm 18,8 pos. C: 20 mm 2L e 2LL pos. D: 15 mm G30 e GPL 3+ e 3B/P 27,7 pos. B: 25 mm 1800 Code Gas kind... -
Page 11: Working Cycle
E031002C 10/04/09 Point 1: door to access to the ironer electric board. This door can be open using the plastic key supplied with the machine documentation. The access to the electric board must be allowed only to specialised and competent personnel. Point 2: the main switch. -
Page 12: How To React In Case Of Entrapment
E031002C 10/04/09 ATTENTION! Please follow strictly the ironing instruction on the clothes label. If no instruction are reported on the linen, please verify the fabric composition before to decide the ironing temperature. Please, pay particular attention to mixed fabrics and tissues with different seams. -
Page 13: Working: Safety Devices Control
E031002C 10/04/09 WORKING: SAFETY DEVICES CONTROL After the machine is switch on, before to start to work, it is compulsory to control the safety device perfect working. Each time the machine is switch on, the user must follow the here below procedure. ACTION REACTION Press the key ON/OFF... -
Page 14: How To Change The Ironing Temperature
E031002C 10/04/09 To start to iron press “ON/OFF”. The display shows the information referring to the temperature and speed. 20°C 5mt/min The displayed temperature is the room one, the speed is the one set. The roller starts to turn. Introduction belts start to turn in the introducing direction. ATTENTION: this ironers must not be use to fold. -
Page 15: How To Change The Ironing Speed
E031002C 10/04/09 While the two keys are used, the set point temperature is shown above on the left of the display. Example: if the ironing temperature to be set is 130°C, keep pressed the increasing key until the display shows: 130°C 5mt/min Once the wished temperature is displayed, leave the temperature increasing key. -
Page 16: Reset Key On The Keypad
E031002C 10/04/09 When this function is on the thermoregulation is interrupted; the display shows that the cooling is activated: 130°C 6mt/min Cooling until 80°C The roller turn until the temperature fall below 80°C. Once this temperature has been reached the machine stop and stay in stand-by mode. -
Page 17: Malfunction: Trouble Shooting - User
E031002C 10/04/09 At the ironing end, and anyway always when the machine is working, the supply system need to be disconnected in the following order: o gas supply (if present): close the supply hose o electric supply: open the electric switch(s) on the back left side bringing it (them) from the position “1”... - Page 18 E031002C 10/04/09 EFFECT POSSIBLE CAUSE Check if: − Electric heated ironer: the heating switch on the back left side is on − Steam heated machine: the steam supply is open − The ironing speed is too much high referring The ironer do not dry enough: the garments come to the linen residual humidity out still wet −...
- Page 19 E031002C 10/04/09 EFFECT POSSIBLE CAUSE The display shows “HANDSAFE” or “SAFE” and the machine stops. Check if: an obstruction is present below the bar. If there HANDSAFE are no dangerous for thinks or people, make the surface free. Call the authorized service centre. SAFE An overheating of the ironing surface occurs: The display shows “OVERHEATING”.
-
Page 20: Drying Ironer Maintenance
E031002C 10/04/09 EFFECT POSSIBLE CAUSE This alarm appears when the safety system of one The display shows “MOTOR OVERHEATING” of the two motors is open or when the inverter fail relay intervenes. If when the alarm is shown, the roller temperature is 140 °C 5mt/min above 80°C, the machine will automatically starts... - Page 21 E031002C 10/04/09 Each month clean the humid air and exhausted gas suction fan in order to take off al the eventual deposits. Grease all the moving mechanisms parts. NOTE: the reducer of the motor is of the kind of permanent lubrication, you do not need to grease it. Each three months clean the internal surface of the ironing roller from dust residuals.
-
Page 22: How To Clean The Burner (Gas Heated Ironer)
E031002C 10/04/09 HOW TO CLEAN THE BURNER (gas heated ironer) Ordinary and special maintenance must be take over only by qualified technician Open the left side using the apposite key. Take off the suction regulator, open the support screw. Take off the flame detector and igniter Take off the burner and clean the external surface using a cloth.