Table of Contents
Advertisement
Quick Links
Connect™ Monitor Manual
FIELD TRIAL PROTOTYPE SAMPLES
Document No:
WT 9437
Issue Date: August 2020
® is a registered Trade Mark of Wellington Drive Technologies
2020 Wellington Drive Technologies Limited
21 Arrenway Dr, Albany, North Shore 0632, New Zealand
PO Box 302-533, North Harbour, North Shore 0751, New Zealand
P:
+64 9 477 0415
Fax:
+64 9 414 6591
E:
info@wdtl.com
www.wdtl.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Wellington Connect Monitor
- Page 1 Document No: WT 9437 Issue Date: August 2020 ® is a registered Trade Mark of Wellington Drive Technologies 2020 Wellington Drive Technologies Limited 21 Arrenway Dr, Albany, North Shore 0632, New Zealand PO Box 302-533, North Harbour, North Shore 0751, New Zealand...
-
Page 2: Installation
No serviceable parts There are no serviceable parts inside the Connect There are no serviceable parts inside the Connect Monitor. Do not attempt to Monitor. open the housing. Opening of the electronics housing, altering, or modifying Do not open the housing. -
Page 3: Correct Disposal
EU Directive 2011/65/EU (RoHS). damaged. Chemicals The Connect Monitor must not be exposed to any solvents or chemicals, as this may damage the housing, leading to unsafe operation. Exposure to such chemicals invalidates the warranty. Temperature The Connect Monitor must only be subjected to temperatures as specified in the “Datasheet”... - Page 4 Connect™ Monitor Instructions Manual FIELD TRIAL PROTOTYPE SAMPLES Introduction The Connect Monitor by Wellington is a battery-operated self- Mobile app with intuitive touch contained Bluetooth LE transmission multifunctional sensor and screen interface data logger designed for providing IoT connectivity to existing ...
-
Page 5: Process Overview
FIELD TRIAL PROTOTYPE SAMPLES Process Overview The following process details the steps required for Connect Monitor installation, commissioning, and activation within the Wellington Connect ecosystem and reporting tools. An NFC phone is required to activate Bluetooth connectivity. These steps are marked with the NFC symbol in the process diagram. - Page 6 • Installation Address • Additional Data • When an asset fitted with Connect Monitor is delivered to a field location, or Photo and Notes • installed in outlet, the following data should be entered through the SCS Field mobile app.
-
Page 7: Physical Installation
FIELD TRIAL PROTOTYPE SAMPLES Physical Installation Position and Location For optimum operation, the choice of physical location and position of the Connect Monitor should meet all the following criteria. If installation in accordance to the below conditions proves to be challenging, please contact your WDTL representative to review appropriate recommendations. - Page 8 Connect™ Monitor Instructions Manual FIELD TRIAL PROTOTYPE SAMPLES FOR COOLERS WITH EVAPORATORS LOCATED AT THE BOTTOM OF THE CABINET: Connect Monitor must be mounted in front of the evaporator inlet. This ensures the Connect Monitor reads the return air temperature correctly.
- Page 9 Connect Monitor is installed facing the wrong way and door openings will not be detected. The front edge of the Connect Monitor should be installed within 70 mm (2 3/4”) of the point where the door seals touch the cabinet wall.
- Page 10 FIELD TRIAL PROTOTYPE SAMPLES Procedure STEP 1 Clean mounting surface using the supplied alcohol wipe. STEP 2 Wait for surface to dry before attaching Connect Monitor. If cabinet is cold, ensure there is no condensation surface prior to attaching the device.
- Page 11 Connect™ Monitor Instructions Manual FIELD TRIAL PROTOTYPE SAMPLES STEP 5 (optional) Insert the two #8 self-drilling screws provided into the mounting holes. Use a standard Phillips head driver to secure screws into the mounting surface (screws will pierce foam tape and seal).
- Page 12 FIELD TRIAL PROTOTYPE SAMPLES Connect Monitor Activation via NFC Prerequisites An NFC capable mobile phone is required to perform Activation on an Connect Monitor. • Prior to initiating the process, check that the mobile phone has NFC enabled. Please refer to the phone user manual for instructions on how to enable NFC.
- Page 13 2. The following message will be visible: “Move your mobile device close to the SCS Monitor you wish to connect to”. 3. Place your mobile phone on top of the Connect Monitor, as depicted, until “CONNECTING MoXXXXXXXX” message is displayed. You may need to hold the...
- Page 14 NFC is successfully enabled on the Connect Monitor. You will be automatically connected to Connect Monitor via Bluetooth for visualization and set up. 5. Upon successful connection you will be prompted with the configuration screen. Please specify the Manufacturer, Owner and Brand.
- Page 15 Connect™ Monitor Instructions Manual FIELD TRIAL PROTOTYPE SAMPLES Please refer to Field App Quick Steps for detailed instructions on how to: WT9403_Set IDs through SCS Connect Field App • WT9404_Set Asset Details through SCS Connect Field App • Available on request. Bulk Activation process through SCS Field Open the SCS Field app and follow the steps below.
- Page 16 Connect™ Monitor Instructions Manual FIELD TRIAL PROTOTYPE SAMPLES 2. “Ready to Scan” screen will be displayed. From this screen, select START BULK ACTIVATION. 3. “Move your mobile device close to the SCS Monitor you wish to activate” message will be visible.
- Page 17 Connect™ Monitor Instructions Manual FIELD TRIAL PROTOTYPE SAMPLES 4. Place your mobile phone on top of the Connect Monitor, as depicted, until “CONNECTING MoXXXXXXXX“ message is displayed. You may need to hold the phone over Connect Monitor for a few seconds to establish an NFC connection.
- Page 18 Connect™ Monitor Instructions Manual FIELD TRIAL PROTOTYPE SAMPLES 7. When all Connect Monitor have been activated, please select STOP BULK ACTIVATION It is vital to configure the device to the correct Manufacturer and Owner. -This feature is NOT supported for Bulk Activation in the Field Trial Prototype units. So...
- Page 19 Check for updates in the App Store or Google Play. Detailed instructions on how to install and activate Field app can be found in Field App Quick Steps, available on request. There are three ways the SCS Field app can connect to the Connect Monitor. All are accessed through the SELECT COOLER page:...
- Page 20 Connect™ Monitor Instructions Manual FIELD TRIAL PROTOTYPE SAMPLES 1. Select NFC from the bottom banner. 2. Hold the phone close to the Connect Monitor you wish to connect to. You may need to hold the phone over the Connect Monitor for a few seconds to establish an NFC connection.
- Page 21 Connect™ Monitor Instructions Manual FIELD TRIAL PROTOTYPE SAMPLES 3. The phone will read the NFC tag inside the Connect Monitor and connect to the device over Bluetooth.
- Page 22 QR CODE 1. Select BARCODE from the bottom banner 2. Point the camera at the QR code included in the Connect Monitor label. FOR FIELD TRIAL UNITS ONLY!! If the device is already installed, the label will be facing the FRONT of the...
- Page 23 Connect™ Monitor Instructions Manual FIELD TRIAL PROTOTYPE SAMPLES 3. The phone will read the QR code and connect to the Connect Monitor over Bluetooth. Google Play Apple Store...
- Page 24 Connect™ Monitor Instructions Manual FIELD TRIAL PROTOTYPE SAMPLES Parameters All parameters are set to read and write by any level of user unless otherwise stated. HIGH TEMPERATURE ALARM SET POINT (not supported in Field Trial Prototype units) Description Parameter Increment & Default Range Units...
-
Page 25: Logging Interval
Connect™ Monitor Instructions Manual FIELD TRIAL PROTOTYPE SAMPLES TEMPERATURE CALIBRATION OFFSET (not supported in Field Trial Prototype units) Increment & Default Description Parameter Units Range The offset amount applied to the Air Temperature parameter -10.0 to 10.0 0.1 °C 0.0 °C to compensate between the measured value and the actual °C Air-Temperature inside the cabinet used by the equipment... - Page 26 Connect™ Monitor Instructions Manual FIELD TRIAL PROTOTYPE SAMPLES Connect Monitor LED Indicator Connect Monitor is equipped with a single LED indicator, used to impart meaningful messages through flashing sequences. The operating scheme is as follows: Connect Monitor State Pattern Purpose...
-
Page 27: Compliance And Approvals
Android with Bluetooth 4.0 and OS 4.4.3 or above iPhone 4S or later iPAD 3rd Gen or later iPAD mini PHYSICAL Dimensions Connect Monitor Overall Dimensions: 107mm (H) x 42mm (W) x 27mm (D) 4.2” (H) x 1.6” (W) x 1.1” (D) Weight 100g (3.5oz) Activity Indicators... -
Page 28: Fcc Declaration
Connect™ Monitor Instructions Manual FIELD TRIAL PROTOTYPE SAMPLES Compliance** CE RED Certification: EN300328 V2.2.2, EN300330 V2.1.1, EN301489- • (includes EMC, RF, Safety&Health) 1&17 & -3, EN62479, EN62368-1, EN60529. FCC: FCC part 15C, 15B • IC ID: RSS247(for Bluetooth)，ICES-003 (EMC), RSS- •... - Page 29 Connect™ Monitor Instructions Manual FIELD TRIAL PROTOTYPE SAMPLES FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 30 Connect™ Monitor Instructions Manual FIELD TRIAL PROTOTYPE SAMPLES Glossary Term Used Definition CE Mark Conformité Européenne. The CE mark signifies that the product conforms to all applicable European Directives required by the European Economic Area (EEA). Cooler Unit The unit containing the refrigeration system and an insulated space for storing and displaying product.
- Page 31 Connect™ Monitor Instructions Manual FIELD TRIAL PROTOTYPE SAMPLES Products Products are the items being stored inside the refrigerated cabinet, for example chilled drinks. Refrigeration System The components comprising the complete refrigeration circuit, including controller, evaporator, expansion valve, condenser, compressor and evaporator fan. Sensor Sensors are devices which generate a signal used to control devices as a result of a detected environmental change.
Need help?
Do you have a question about the Connect Monitor and is the answer not in the manual?
Questions and answers