Advertisement
Quick Links
Advertisement
Summary of Contents for latch Hub
- Page 1 Installation Guide...
-
Page 2: Table Of Contents
Table of contents Things you should know Included in the box Product details Installation Specifications Document number 770-00015 Requirements for compliance Revised on 08/26/2020... -
Page 3: Things You Should Know
Mounting Tools • #2 Phillips head screwdriver • T25 Torx screwdriver • 1/4” drill bit For in-unit install, place the hub near the media panel. Requirements for Device • 64 bit iOS device Configuration requires the iOS Manager App running •... -
Page 4: Product Details
Product Details Details and recommendations for power, wiring, and product specifications. Hub Installation Guide Version 1.0... - Page 5 Solid White - Online and connected Flashing White - Booting up, connecting, or pairing Fast Flashing White - Firmware updating Solid Red - Cannot connect to Latch servers No Light - Power off or battery out Hub Installation Guide Version 1.0...
- Page 6 Input frequency: 47 - 63 Hz Output voltage: 12 VDC +/- 5% Max load: 2 AMPs Min load: 0 AMPs Load regulation: +/- 5% 2.5mm barrel jack 5ft cable length Note: Do not splice DC power adapter Hub Installation Guide Version 1.0...
- Page 7 5ft cable length 5ft cable length Sold Separately. Note:If the DC power adapter (5ft) is not long enough for installation, an additional 5ft extension cable can be used. Only one extension per hub is supported. Hub Installation Guide Version 1.0...
- Page 8 Low Voltage 2 Wire Power Distance < 25ft < 50ft < 100ft < 200ft Power (12v) 24 AWG 22 AWG 18 AWG 14 AWG In- Building 12VDC > 24 Watts Power Supply *Class 2 Isolated, UL Listed Hub Installation Guide Version 1.0...
- Page 9 12mm x 2.5mm x 5.5mm Operating 0° - 40°C (32°F - 104°F) Temperature Required FCC Part 15, EN61000-4-2, EN61000-4-3 Certifications Additional Features Overload and short circuit protection (Preferred) PoE Switch/Injector: 802.3at/802.3bt 30W+ Note: Daisy Chain not supported. Hub Installation Guide Version 1.0...
-
Page 10: Installation
Installation Follow these steps to proceed with installation. Hub Installation Guide Version 1.0... - Page 11 Rotate Torx screws in outer Cover counter-clockwise to unlock. Separate the outer Cover from the Mounting Plate using the opening on the underside. Rotate Torx screws in Hub counter-clockwise to unlock. Remove Note: Do not use a power tool or excessive force on the Torx screws—over torquing could cause damage.
- Page 12 Attaching to junction box Attaching to wall or ceiling Install Mounting Plate. Attach to junction box or attach to wall or Note: Pass cables through opening before attaching Mounting ceiling. Plate to junction box. Hub Installation Guide Version 1.0...
- Page 13 Attach Hub to Mounting Plate by aligning mating features. Rotate Torx screws in Hub clockwise to lock. Hub Installation Guide Version 1.0...
- Page 14 Plug in power and Ethernet cables. Use included cable ties to secure. Install Grommet. Junction box scenario. Hub Installation Guide Version 1.0...
- Page 15 Use Latch Manager App to setup the device. Observe and Install the outer Cover aligning with Mounting Plate and Grommet. monitor LED to verify set up success. Rotate Torx screws clockwise to lock and secure Cover. Hub Installation Guide Version 1.0...
-
Page 16: Specifications
• FCC Part 15B / 15C / 15E / 22H / 24E • IC RSS-210 / 139 / 133 / 132 / 130 / 102 (MPE) • UL 62368 • ICES-003 • CEC/DOE • NRCAN PTCRB IEC62133 (Battery) Hub Installation Guide Version 1.0... - Page 17 To reduce potential safety issues, only the battery provided with the product, a replacement • battery provided by Latch, or a compatible battery purchased as an accessory from Latch Pour remplir les conditions requise sur l’exposition des fréquences radios, cet appareil et les should be used with the product.
Need help?
Do you have a question about the Hub and is the answer not in the manual?
Questions and answers