Advertisement
GUIDING SYSTEMS
Displays either the gain or
a system status code.
Det 1 Guide
Lit when the system is
guiding with detector 1
(edge 1).
Det 2 Guide
Lit when the system is
guiding with detector 2
(edge 2).
Center Guide
Lit when the system is
guiding with both
detectors (center guide);
blinks when in web setup.
Detector Select: Selects the detector or
detectors used for control: edge 1 allows
guiding from detector 1 only, edge 2 from
detector 2 only, and center guide from both
.
detectors
Servo Center: Switches control to servo center.
In servo center, the actuator travels to a preset
center position. Exit servo center control by press-
ing either manual or automatic.
Manual Control: Switches control to manual, al-
lowing the operator to jog (reposition) the actuator.
Jog using the arrow keys. Exit manual by pressing
automatic or servo center .
Automatic Control: Switches control to auto-
matic. Exit automatic by pressing either manual
or servo center.
H6415-DSP (REMOTE USER INTERFACE)
SYMBOL DEFINITION KEY
Bar graph indicates relative strip
position. Middle block shows the
ideal web position.
MAINT. SHEET
Gain Adjust Mode Indicator.
H6415
Amplifi er in automatic mode;
blinks when the line-run relay input
is energized in automatic.
Amplifi er in
manual mode.
Amplifi er in servo center mode.
User keys
(see below).
Web Setup: In this mode, the amplifi er is informed
of the detector(s) and web characteristics. 1) Press
manual key. 2) Press this key. 3) Pass the web
material fully into, then fully out of the detector's
fi eld of view. Do not let fi ngers or printing on
the web enter the fi eld of view. 4) Press key
again. If pressed accidently, press any green key
to escape.
Left Jog Key: Used to manually jog the actuator
left or to decrease the gain.
Right Jog Key: Used to manually jog the actuator
right or to increase the gain.
Gain: Used to adjust the control response. Press
this key, then use the arrow keys to increase or
decrease the system response (0-999). Press
again to accept the value and to exit this mode.
10028
MS-17.00
January 2000
Advertisement
Table of Contents
Summary of Contents for FIVES NORTH AMERICAN H6415-DSP
- Page 1 10028 MAINT. SHEET MS-17.00 GUIDING SYSTEMS January 2000 H6415-DSP (REMOTE USER INTERFACE) SYMBOL DEFINITION KEY Bar graph indicates relative strip position. Middle block shows the Displays either the gain or ideal web position. a system status code. Gain Adjust Mode Indicator.
- Page 2 Set voltage select switch (SW201) in the controller Wire ground (GND) and AC power connections If communicating with more than one H6415-DSP or through a computer, then defi ne the primary interface with (SW101) in the H6415-DSP; otherwise, skip this step.
Need help?
Do you have a question about the H6415-DSP and is the answer not in the manual?
Questions and answers
Como calibrarlo
To calibrate the FIVES NORTH AMERICAN H6415-DSP:
1. Press the "Gain" key.
2. Use the arrow keys to adjust the system response between 0 and 999.
3. Press the "Gain" key again to accept the value and exit.
For detector alignment:
1. Press the manual key.
2. Pass the web material fully into, then out of the detector’s field of view (avoid fingers or printed areas).
3. Press the key again to complete the calibration.
You can switch control modes using:
- "Manual Control" to jog the actuator manually.
- "Automatic Control" for automatic operation.
- "Servo Center" to center the actuator.
Exit any mode by pressing another control mode key.
This answer is automatically generated
funcionamiento de regulación de equipo, para ajustar el registro de lector de banda
The regulation function for the FIVES NORTH AMERICAN H6415-DSP equipment to adjust the band reader register involves selecting the appropriate guiding mode and adjusting system parameters. The user can choose between guiding with detector 1 (Edge 1), detector 2 (Edge 2), or both detectors (Center Guide). The gain can be adjusted using the Gain Adjust Mode Indicator, and the system response can be modified by pressing the Automatic Control key and using arrow keys to set the response level (0-999). Additionally, the Web Setup Procedure informs the amplifier of the detector(s) and web characteristics to ensure proper alignment and tracking.
This answer is automatically generated