Summary of Contents for Antona ANC-7030
- Page 1 Rev. A ANC - 7030 Marquee/Page/Clock Controller Antona Corporation, Los Angeles, CA Antona Corporati on URL:antona.com TEL:(818)783-4299...
- Page 2 THE PURCHASER MUST OBTAIN A RETURN AUTHORIZATION FROM THE ANTONA CORPORATION PRIOR TO RETURNING ANY PIECE OF EQUIPMENT. Shipment to the Antona Corporation will be at the expense of the purchaser; return shipment will be at the expense of the Antona Corporation for all warranty repairs.
-
Page 3: Table Of Contents
4.22 Marquee Setting............................. 8 4.23 Time-of-Day Setting ..........................8 4.24 Clock Brightness Setting......................... 8 4.25 Clock LED Test............................9 APPENDIX A - CLOCK PROTOCOL......................10 APPENDIX B - CHASSIS SCHEMATICS....................... 11 APPENDIX C - RF TRANSMITTER AND RECEIVER................. 14 Antona Corporation (818)783-4299 URL:http://www.antona.com... -
Page 4: Features
4" X 12" time-of-day clock (Antona ANC-7020). The internal chassis hardware consists of an Antona ANC-7852 8052 microcontroller card and an ANC-7332 real time clock input/output card. An ANC-6090 RS422 output adapter handles transmitting the differential signal to the external wall mounted clocks. -
Page 5: Installation
Install the ANC-7030 chassis into any empty 1 unit high rack mount opening and secure the chassis to the enclosure. Connect any external cabling for serial output, RF antenna, powering or audio output before applying power. -
Page 6: Page Operation
If the unit is equipped with one or more ANC-7020 remote reading large format clocks, the ANC-7030 chassis will transmit the currently set time displayed on the LCD in military format (00:00 to 23:59). The remote clocks are all updated with time information each second. -
Page 7: Chassis Operation And Settings
Aside from the power supply detailed in 4.11, the only other input connector is located on the rear right hand side of the chassis labeled "PAGE ANT" for connection of the external pager antenna by way of a BNC type connector. The antenna input Antona Corporation (818)783-4299 URL:http://www.antona.com... -
Page 8: Chassis Software Operation
At any time, the user may press the "Help" button to review how to use any of the ANC-7030 settings. In help mode, use the "Up Arrow" and "Down Arrow" to scroll through the instructions on the LCD. Use the number buttons to get specific instructions on the various modes. -
Page 9: Clock Led Test
This mode is mostly for factory use. Its purpose is to turn all LEDs on for one (1) minute, and then return to normal clock display operation. Once this mode is entered, the user may return to normal operation by pressing the "Clear" button. Antona Corporation (818)783-4299 URL:http://www.antona.com... -
Page 10: Appendix A - Clock Protocol
31H = set clock test LED mode - turn all LEDs on A typical serial transmission of time data would be as follows: CCH 80H 21H 12H 34H 0AH This would display "12:34" on all connected and powered ANC-7020 units. Antona Corporation (818)783-4299 URL:http://www.antona.com... -
Page 11: Appendix B - Chassis Schematics
Appendix B - Chassis Schematics The following page(s) contain the schematics for the ANC-7030 chassis. The schematics are included to aid the end user in configuring the chassis, or for competent technical service personnel to use in maintenance or repair. - Page 12 Antona Corporation (818)783-4299 URL:http://www.antona.com...
- Page 13 Antona Corporation (818)783-4299 URL:http://www.antona.com...
-
Page 14: Appendix C - Rf Transmitter And Receiver
The following page(s) contain the product technical data for the 318MHz hand held key-chain transmitter and the mating RF receiver used with the ANC-7030 chassis. This information is available to current owners of the ANC-7030 by FAX or in PDF format by e-mail. A specific e-mail with the subject: "ANC-7030 RF318"...
Need help?
Do you have a question about the ANC-7030 and is the answer not in the manual?
Questions and answers