Presentation of each mode Switch from one mode to another TEST THE VIBBY OAK Demo Mode SET-UP WITH THE MOBILE APPLICATION Presentation of the application Connecting the Vibby OAK to the application p 10-11 Use of the application p 12...
INTRODUCTION PREAMBLE Vibby OAK is a smart intentional alarm system that, in some cases, adds additional protection if the user is not able to manually raise the alarm. The Vibby OAK is designed to automatically detect heavy/ dangerous falls (sudden and quick loss of balance followed by a significant impact of the body with the floor leaving the user lying on the floor unable to recover to a standing position).
SOS button or the Vibby OAK detects an about to be sent. manner. abnormal activity. stand up. REMINDER: The Vitalbase technology does not allow the analysis all fall situations.
. AUTOMATIC ALARM An evidenced SOS button is located in the Multiple sensors combined with a new, middle of the Vibby OAK. By pressing this innovative algorithm can automatically raise button the wearer can himself raise an an alarm when a heavy fall is detected.
* If the Vibby OAK is in neck worn mode, you have to press a little longer (half a second). What is the storage mode? How do I know if the Vibby OAK is in...
SWITCH FROM ACTIVE MODE TO STORAGE MODE Before the red LED goes off, press The Vibby OAK will vibrate and its Put the Vibby OAK flat on a table. Press the button until the red LED the button quickly and successively...
The manual alarm can be tested by simply pressing the button. The Vibby OAK will Drop the Vibby OAK on the ground, After a period of 20 sec. the Vibby OAK will vibrate and vibrate and the red LED illuminate. at a person’s height.
SET-UP WITH THE MOBILE APPLICATION PRESENTATION OF THE APPLICATION THE VIBBY OAK CAN BE EASILY SET UP BY USING A DEDICATED MOBILE APPLICATION: Wearing mode selection : wrist or pendant Radio protocol selection The application also displays essential information: Battery status...
Once identified*, you are redirected to the page « search for Vibby OAK » (see opposite). All you need to do now to connect the Vibby OAK to the application is to follow the procedure on the next page. IMPORTANT: TO CONNECT TO THE APPLICATION, YOU NEED A LOGIN AND A PASSWORD.
Page 11
CONNECTING THE VIBBY OAK TO THE APPLICATION Familiarise yourself with all steps before starting the procedure. You need to be identified by the application. The latter has to be in “search for Vibby OAK” mode: 3 sec. 8 sec. Make sure that the Vibby OAK is in Press the button until the second series of red flashes starts and then release immediately.
SET-UP WITH THE MOBILE APPLICATION USE OF THE APPLICATION Vibby OAK serial number Battery status Selection of wearing option Selection of protocol option...
Page 14
VIBBY OAK - FACT SHEETS 1 AUTOMATIC FALL DETECTION SENDING OF THE ALARM After 20 seconds, the alarm will be sent to the partner device. The Vibby OAK will vibrate and the red LED light up for 2 seconds. SILENT ANALYSIS ALERT After a fall, the Vibby OAK will analyse the person’s...
Page 15
VIBBY OAK - FACT SHEETS 2 THE DIFFERENT MODES CONFIGURATION MODE Set-up of wearing mode Set-up of radio protocol STORAGE MODE ACTIVE MODE...
Page 16
8 sec. 60 sec. You have 1 minute to perform the next step Make sure that the Vibby OAK is in storage Press the button until the 2 series of red flashes starts and then release immediately. (step 4). If the green LED goes off, go back to mode (see installation guide pages 6 and 7).
Page 17
VIBBY OAK - FACT SHEETS 4 VERIFICATION OF WRIST / PENDANT MODE HOW DO I KNOW IF THE VIBBY OAK IS IN WRIST MODE? Quickly press the button twice and then The red LED flashes quickly. The Vibby OAK vibrates.
Page 18
Press the button until the 2nd series of red flashes starts and then release immediately. mode (see installation guide pages 6 and 7). (step 4). If the green LED goes off, go back to step 2. Press the button and hold it until the Vibby OAK will vibrate and then release immediately. PROTOCOLS PROTOCOLS...
Page 19
VIBBY OAK - FACT SHEETS 6 BATTERY REPLACEMENT Use the Vibby OAK battery extracting tool and replace the battery in 7 steps: Take the extracting tool to remove Make 1/4 of a turn with the tool. Remove the cover. Replace the used battery.
Page 20
FITTING THE WRIST / PENDANT The fitting of the wrist strap /neck cord of the Vibby OAK must be carried out by an installer in storage mode. The fitting is therefore deliberately difficult so that the user or his family cannot easily perform it themselves.
Page 21
REMOVING THE WRIST / PENDANT The fitting of the wrist strap /neck cord of the Vibby OAK must be carried out by an installer in storage mode. The fitting is therefore deliberately difficult so that the user or his family cannot easily perform it themselves.
Page 22
- Overloaded Bluetooth environment. - Check your identifiers and try to reconnect. - Wait for 5 min., make sure that the Vibby OAK is in - The application dos not have the necessary rights. storage mode and restart set-up from the beginning.
Page 23
The Vibby OAK is a smart intentional alarm system that, in some cases, adds additional protection if the user is not able to manually raise the alarm. The Vibby OAK is designed to automatically de- tect heavy/dangerous falls (sudden and quick loss...
Need help?
Do you have a question about the Vibby OAK and is the answer not in the manual?
Questions and answers