3M Post-it Dry Erase Surface Quick Start Manual

Recommended Surfaces:
The Post-it Super Sticky Dry Erase Surface is designed to stick to a variety of primed and painted drywall and steel surfaces,
®
glass, finished wood, and existing whiteboards or chalkboards. Not recommended for use on unprimed drywall, cinder block,
brick, wallpaper, heavily textured, or delicate surfaces.
Surface Preparation:
Surfaces to be covered must be clean, smooth, dry and structurally sound – must not contain loose paint, nail heads, nicks,
gouges, or other surface imperfections. For best results, gently clean the surface to be covered with water and soft cloth, allow
to dry for 10 minutes. If walls have been recently painted, allow paint to cure according to paint instructions before applying the
Post-it Super Sticky Dry Erase Surface.
®
Cutting the Film:
The Post-it Super Sticky Dry Erase Surface can be cut to size using a variety of cutting tools including scissors, box cutters or
®
utility knives. Always confirm the size of the area you wish to cover, measure the surface twice before cutting and use a straight
edge, such as a ruler, to ensure a square cut. Take caution when handling the edges of the film as they may be sharp.
Use and Maintenance Procedures:
• Use standard dry erase markers.
• Erase ink with the provided Post-it
• Erase ink when content is no longer needed.
• When needed to remove ink buildup, use a microfiber cloth with water or whiteboard cleaning spray. Wet-cloth cleaning
is recommended once per week.
• Never use permanent markers or pens. To remove permanent marker, write over the mark with a dry erase marker,
then wipe it off or gently clean with isopropyl rubbing alcohol.
• Writing or erasing marker dust off the film and onto the wall may result in staining. Gently clean wall with household
cleaner or isopropyl rubbing alcohol.
• Do not scratch the white film.
Product Removal:
To remove the Post-it Super Sticky Dry Erase Surface, select a corner of the film and peel slowly and smoothly away from the
®
wall. For best results, gently pull away at a 180 degree angle. CAUTION: Pulling the film away from the wall in a fast or
aggressive motion may result in film or surface damage.
Safety Information:
CAUTION: To reduce the risks associated with sharp edges, use caution when handling, cutting and installing the product.
Warranty Information:
Limited Warranty
Product will be free from defects in material and manufacture when used as directed for indoor vertical applications only,
for 3 years from purchase date. Not covered: normal wear and tear, or damage from accident, misuse, alteration or lack of
reasonable care. 3M will, at 3M's option, replace or repair product or refund purchase price upon receipt of proof of purchase.
Warranty valid only for products sold in USA and Canada and gives you specific legal rights. You may have other rights which may
vary from state to state or province to province. To obtain warranty service in USA, contact 3M at 1-800-395-1223, and in Canada,
contact 3M at 1-800-364-3577.
Limitation of Liability
3M will not be liable for any loss or damage arising from use of this product, whether direct, indirect, special, incidental or
consequential, regardless of the legal theory asserted, including warranty, contract, negligence or strict liability. Some states,
provinces and countries do not allow the exclusion of limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you.
Stationery & Office Supplies Division
3M Center, Building 223-3S-03
St. Paul, MN 55144-1000
1-800-395-1223
DRY ERASE SURFACE
Dry Erase Cleaning Cloth or microfiber cloth. Felt erasers are not recommended.
®
3M and Post-it are trademarks of 3M. Used under license in Canada.
Please recycle. Printed in U.S.A.
© 3M 2018. All rights reserved.
70-0052-9221-7 34-8722-9585-1