Advertisement
Table of Contents
MEDIUM
GARDEN SHED
2280mm wide x 1530mm deep x 1980-1830mm high
ASSEMBLY
INSTRUCTIONS
YOU SHOULD HAVE TWO PACKAGES:
• 1 cardboard package
• 1 channel pack
TOOLS REQUIRED:
• Battery or electric drill
• 3.3mm (1/8th inch) drill bit
• Screwdriver or riveter
• Tape measure
• Ladder
• Non-slip gloves, good shoes and goggles
• A set of helping hands
Some parts have sharp edges and should be handled very carefully.
We recommend the use of protective gloves and footwear when assembling.
DO NOT attempt to erect this shed in windy weather. All dimensions are approximate.
CALL 0508 454 873
for an installer near you
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Number 8 NO8 MEDIUM AZ
- Page 1 MEDIUM GARDEN SHED 2280mm wide x 1530mm deep x 1980-1830mm high ASSEMBLY INSTRUCTIONS YOU SHOULD HAVE TWO PACKAGES: • 1 cardboard package • 1 channel pack TOOLS REQUIRED: • Battery or electric drill • 3.3mm (1/8th inch) drill bit • Screwdriver or riveter •...
-
Page 2: Components Checklist
COMPONENTS CHECKLIST Please check the parts carefully and advise immediately if any are damaged or missing. 1 x 1920 x 780mm door sheet 2 x 1980 x 740mm sheets 3 x 1830 x 780mm sheets for back wall (Beside front door) 3 x 1770mm x 780mm sheets for roof 4 x 1980-1830mm sloping sheets 6 x 2255mm 'U' channels for... -
Page 3: Door Assembly
STEP 1 DOOR ASSEMBLY YOU WILL NEED 1 x 1920 x 780mm door sheet Attach the 780mm 'U' channels to the top and bottom of the door sheet 2 x 1920mm 'U' channels for door sides at the centre ribs only. Attach the 1920mm 'U' channels to the door 2 x 780mm 'U' channels (door top through the top and bottom channels... -
Page 4: Front Wall
Channels will come short WASHER of the ends of the sheeting by 10-15mm on all panels. RIVET NUMBER 8 TIP FITTING CHANNELS The higher side of the channel goes to the To hinge the door on the opposite inside of the shed. It is very important to... - Page 5 Fix the channels through the end ribs and every second rib in between. Make sure you put at least one fixing per sheet up through the underside of the channel into the pan of the sheet. NUMBER 8 TIP Put extra fixings in for high wind areas, particularly on the underside.
- Page 6 STEP 6 END WALLS YOU WILL NEED 4 x 1980-1830mm sloping sheets Cap the sloping sheets with the 'U' channels (2 left, 2 right) Fix the channels through the end ribs and every second rib in between. Make sure 4 x 1485mm 'U' channels for side walls you put at least two fixings up through the underside of the channel into the pan of the sheet.
-
Page 7: Installation
It is essential that every shed has a floor, but the only way to make sure your shed is there to stay on windy sites is with a recessed concrete floor. NUMBER 8 TIP • Visit your local Mitre 10 store for floor options... - Page 8 STEP 9 COMPLETE YOUR SHED RECESSED CONCRETE FLOOR PLAN FOR SPECIALLY POURED CONCRETE FLOORS: SPECIFICATIONS Every shed must have some type of foundation (Flooring) between it and the ground. You can pour a concrete floor and use recessed floor clamps, use an existing concrete base with flat floor clamps or purchase a kitset wooden floor from your local Mitre 10 store.
Need help?
Do you have a question about the NO8 MEDIUM AZ and is the answer not in the manual?
Questions and answers