Table of Contents
Advertisement
Quick Links
Kozy-World
ACCESSORY INSTALLATION
WARNING: ELECTRICAL GROUNDING INSTRUCTIONS This
appliance is equipped with a three-prong (grounding) plug for your
protection against shock hazard and should be plugged directly into
a properly grounded three-prong receptacle.
Questions about installation, operation, or troubleshooting?
Befor e r etur ning to your r etailer, call KOZY WORLD at 1-800-
20-6030 BLOW ER
INSTRUCTIONS
776-9425.
®
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Kozy-World 20-6030
- Page 1 Kozy-World ® 20-6030 BLOW ER ACCESSORY INSTALLATION INSTRUCTIONS WARNING: ELECTRICAL GROUNDING INSTRUCTIONS This appliance is equipped with a three-prong (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle.
-
Page 2: Package Contents
PACKAGE CONTENTS Parts included with this kit Item Part No. Description XB001-01 Power Cord XB002-01Q Blower... - Page 3 SAFET • Connect to properly grounded outlets only. IMPORTANT: Read all instruc- • This appliance, when installed must be tions and warnings carefully electrically grounded in accordance with before starting installation. Fail- local codes, with the current CSA C22.1 ure to follow these instructions Canadian Electrical Codes or for USA installations, follow local codes and the...
- Page 4 PREPARATIO Tools Required • Phillips Screwdriver • Wire Cutter GFD2545, see page 4. GSD3033, GFD4360 and GSD4400, see page 8 BLOWER INSTALLATION - GFD2545 Protection Tab Install Power Cord and ...
-
Page 5: Installation
INSTALLATION - GFD2545 4. Attach the grounding terminal to top cover WARNING: Before installing with 1) M4.2X8 screw (AA). Refer to wiring the blower, be certain to turn off diagram, page 15. Be sure to insert the gasket between the protection tab and the unit, and allow time for unit the grounding terminal (see Figure 4). - Page 6 INSTALLATION - GFD2545 Insert the female port, which is on the 9. Attach temperature sensor to the back of white power supply wire (marked with P1), the firebox with 2) M4.2X8 screws (AA) into the corresponding male port (marked (see Figure 9).
- Page 7 INSTALLATION - GFD2545 12. Remove 2 screws securing grill to stove 16. Connect the AUTO, OFF, MAN wires to front. Carefully set grill aside (see Fig- the three corresponding male tabs on the ure 12). rocker switch (see Figure 15). ...
- Page 8 INSTALLATIO GSD303 Install Temperature Install Wiring and Install Blower Sensor Grounding Terminal Install Rocker Switch GSD4400 Install Temperature Sensor Install Install Blower Wiring and Grounding Terminal ...
- Page 9 INSTALLATIO www.wor ldmkting.com 200071-01A ...
- Page 10 INSTALLATION - GSD3033, GSD4400 AND GFD4360 4. Attach the temperature sensor to the back WARNING: Before installing of the firebox with 2) M4.2X8 screws (AA) (see Figure 21). the blower, be certain to turn off the unit, and allow time for unit to cool down.
- Page 11 INSTALLATION - GSD3033, GSD4400 AND GFD4360 6. Connect two black and yellow wires (fe- Insert the blower connector (male port) male ports) marked T1 and T2 with the into the female port on the wire connector. two male ports on the temperature sensor This protects the jacket in the fireplace (see Figure 23).
- Page 12 INSTALLATION - GSD3033, GSD4400 AND GFD4360 12. Bundle the wiring with the cable tie (see 15. GSD3033 Remove screws securing front Figure 29). Attach cable tie to the stove log bracket and control panel (see Figure through the hole as shown in Figure 29. 31a).
- Page 13 INSTALLATION - GSD3033, GSD4400 AND GFD4360 16. Feed the AUTO, OFF, MAN connectors 18. Push the rocker switch into the control through the rocker switch hole on the left panel (see Figure 34). side of the control panel (see Figure 33). ...
-
Page 14: Electrical Connection
ELECTRICAL CONNECTION A 15 amp, 120 Volt, 60 Hz circuit with a properly grounded outlet is required. The WARNING: Electrical outlet fireplace should be on a dedicated circuit. wiring must comply with local Other appliances on the same circuit may building codes and other appli- cause the circuit breaker to trip, or the fuse to cable regulations to reduce the... -
Page 15: Operation
OPERATIO Using rocker switch, turn blower on and position the blower will be controlled by the check for operation. Turn on rocker switch to temperature sensor. To stop the operation turn the desired position. In the MAN position the rocker switch to the O position. -
Page 16: Electrical Wiring Diagram
ELECTRICAL W IRING DIAGRAM Any electrical re-wiring of this appliance must be done by a qualified electrician. This wiring WARNING: If repairing or must be done in accordance with local codes replacing any electrical compo- and/or in Canada with the current CSA C22.1 nent or wiring, the original wire Canadian Electrical Code, and for US instal- routing, color coding and secur-... - Page 17 Kozy-World ® World Marketing of America, Inc. PO Box 192, Rt. 22 West MillCreek, PA 17060 200071-01 www.worldmkting.com Rev. A...
Need help?
Do you have a question about the 20-6030 and is the answer not in the manual?
Questions and answers