Inserting/Changing Batteries - easymaxx U-SLLR01 Operating Instructions Manual

Inserting/changing batteries

LED light
You will need 3 x 1.5 Volt bat-
teries of type AAA. They are
not included in the product
contents!
1. Screw open the battery compart-
ment on the back of the product.
2. Remove the empty batteries and
dispose of them in an environmen-
tally-friendly manner.
3. Insert 3 x 1.5 Volt AAA batteries.
When inserting batteries, always
make sure that the polarity is cor-
rect (+/–).
4. Screw down the battery compart-
ment securely.
Remote control
The battery for the remote
control has
inserted. You only have to
remove the transport guard.
1. Push the catch on the battery
compartment to the right using your
fi nger nail and pull out the battery
compartment at the same time.
2. Remove the empty battery and
dispose of it in an environmental-
ly-friendly manner.
3. Insert a 3 Volt battery of type
CR2025. When inserting batteries,
always make sure that the polarity
is correct (+/–).
4. Place the battery compartment back
into the remote control. It must audi-
bly lock into place.
Start-up
The product is suitable for use
in wet environments (e.g. vas-
es, ponds, fl ower beds etc.).
Before use, always ensure
that the battery compartment
is securely screwed down to
prevent water from penetrating
the product.
1. Unpack the product contents and
remove any protective foils and
stickers. Check all parts for any
damages from transport. Should
you identify any transport damages,
please promptly consult customer
service.
2. Place the LED light in the area to
be illuminated (e.g. vases, shelves,
fl ower pots, pond etc.).
3. Turn on the LED light by pushing the
ON button on the remote control.
Customer service / importer:
DS Produkte GmbH, Am Heisterbusch 1, 19258 Gallin, Germany
Tel.: +49 (0) 38851 314650
All rights reserved.
09267_DE-GB-FR-NL_140x297cm_V1.indb 4 09267_DE-GB-FR-NL_140x297cm_V1.indb 4
4. Select the desired colour or the
desired effect and push the corre-
sponding button on the remote con-
trol.
Please note that the colour
settings are mixed colours.
For this reason, the colour tints
may exhibit minor deviations.
Even white light is a mixed col-
our and thus not a purely white
colour tint!
5. Set the desired colour brightness
using the buttons to increase/de-
crease the intensity of colour.
6. Push the OFF button to turn off the
LED light.
Technical data
Product number: Z 09267
Model number:
Power supply:
Light:
already been
Remote control: 3 V (1 x 3 V battery,
Disposal
The packaging material is re-
cyclable. Dispose of the pack-
aging in an environmental-
ly-friendly manner and make it
available to the collection ser-
vice for recyclable materials.
Dispose of the product in
an
manner. The product does
not belong in the household
garbage. Dispose of it at a
recycling centre for old electric
and
For more information, please
contact the administration in
your community.
Batteries and storage batteries
must be removed and disposed
of separately before disposing
of the product. To protect the
environment,
rechargeable batteries may
not be disposed of together
with normal household waste.
Instead they must be turned
in at appropriate collection
points. Please also observe
applicable statutory provisions
regulating
batteries.
(Calls subject to a charge.)
U-SLLR01
4.5 V (3 x 1.5 V
batteries, type AAA)
type CR2025)
environmentally-friendly
electronic equipment.
batteries and
the disposal of
06.02.2015 10:42:51 06.02.2015 10:42:51