LAZER XLZSHR070L Owner's Manual

Wood

Hide thumbs

Table Of Contents

Quick Links

Download this manual

Wood Shredder Chipper

Owner's Manual

REV062117 CPR070

Table of Contents

Summary of Contents for LAZER XLZSHR070L

Page 1 Wood Shredder Chipper Owner’s Manual REV062117 CPR070...
Page 2: Table Of Contents
Table of Contents Safety Instruction……………………………………………..………………………….3-5 Working with the shredder………………………………………………………..…..6-8 Maintenance and checks…………………………………………………………..………9 Problems and solution……………………………………………………………………10 Hardware and Package …………………………………………………….……….11-12 Assembly instruction…………………………………………………………….……13-16 Technical specifications………………………………………………………………….17 Spare parts drawing………………………………………………………………………18 Spare parts list…………………………………………………………………………29-20...
Page 3: Safety Instruction
SAFETY INSTRUCTION GENERAL SAFETY WARNINGS  It is important you read and understand the instruction manual before first use and keep the manual in a safe place for future reference.  Safety precautions must be observed to reduce the risk of personal injury when operating this machine.
Page 4 TRANSPORTING THE MACHINE  Always turn off the engine.  The engine should be turned off when the machine is moved between areas and when transporting or storing the machine.  When transporting in a vehicle: properly secure your machine to prevent turnover, fuel spillage and damage.
Page 5 1. Intended use The shredder is designed solely for shredding/chipping all kind of newly cut tree branches of diameter up to 6cm. 2. Components of Machine 3. Symbols N.B.: Before use, make sure that the manual has carefully read. Because familiar with the controls so as to use the machine correctly.
Page 6: Working With The Shredder
Working with the shredder 1. Safety and technical remarks 1.1. The user should be 18 years old or more. 1.2. The machine should be positioned on a horizontal. Firm surface. 1.3. User must wear safety gloves (not provided with this unit), ear-protection and safety goggles. (fig.4) 1.4.
Page 7 2. Before operating the machine Make sure the machine stands firmly on the ground and does not tilt in any way. The danger zone on the output of the machine must be respected, in order to avoid serious injury by chips thrown out of the output tube.
Page 8 Fig.10 Fig.11 Fig.13...
Page 9: Maintenance And Checks
4. Transport Before moving the machine, stop the engine! Maintenance and checks All technical check-ups and maintenance should be done with the engine shut off and the spark plug cap removed from the spark plug. While cleaning the shredder, never spray the bearing with a high pressure washer! It could cause water to enter the bearings which will cause damage to the machine;...
Page 10: Problems And Solution
Problem & Solutions Problem Cause Solution The shredder does not -the blades are worn too -change sharpen blades perform properly: the much counter-blade. Note that the blades are wood is not pulled in by -the diameter sharpened on both edges so they can be the machine itself.
Page 11: Hardware And Package
Hardware Contents When unpacking, check to make sure all the parts shown on the below diagram are included.
Page 12 Package Contents...
Page 13: Assembly Instruction
ASSEMBLY INSTRUCTION Step 1: Attach wheel axle (#24) and wheel (#6) to the base (#1) using hex bolt M8x25 (#26), lock washer Ø8 (#27) and flat washer (#25). Tighten the wheel axle (#24) using hex bolt M6x12 (#16) and hex nut M6 (#52). Attach support leg assembly (#43) to the base (#1) using hex bolt M8x20 (#62), lock washer Ø8 (#27) and flat washer Ø8 (#50).
Page 14 Step 2: Lock handlebar (#8) and base (#1) using key ring (#23), pawl (#22) and spring (#21). Then fixed with hex bolt M10x60 (#33), flat washer Ø10 (#54) and nylon lock nut M10 (#68).
Page 15 Step 3: Attach the inlet hopper assembly (#5) to the roller cover plate assembly (#20), then fixed with shredder hopper (#3) using hex bolt M8x20 (#62), lock washer Ø8 (#27) and large flat washer Ø8 (#64)
Page 16 Step 4: 1. Attach the output hopper assembly (#9) to the roller cover plate assembly (#20), then fixed with shredder hopper (#3) using hex bolt M8x16 (#61), lock washer Ø8 (#27) and large flat washer Ø8 (#64)
Page 17: Technical Specifications
Technical specifications Engine: 4 stroke Maximum rpm: 3600 Fuel: lead free petrol Shredding system: 2 blades on rotor and 1 counter-blade on the chassis. Blades are sharpened on both edges so they can be reversed. Transmission : twin V belts running in parallel Dimensions: Max.
Page 18: Spare Parts Drawing
PARTS DRAWING...
Page 19 PARTS LIST Drawing No. Ref# Description CPR070-01000 Base Weldment CPR070-02100 Roller Wdlement CPR070-03000 Shredder Hopper CPR070-00002-DY Striker Plate CPR070-04000 Inlet Hopper Assembly CPR070-10000 Wheel Engine CPR070-05000 Handlebar CPR070-06000 Output Hopper Assembly CPR070-00005 Baffle CPR070-00007 Belt Pulley CPR070-00008 Engine Belt Pulley CPR070-00009-DX Engine Bushing CPR070-07000...
Page 20 PARTS LIST Drawing No. Ref# Description CPR070-00014 Mound Layer CPR070-13000 Emergency Switch CPR070-11000 Support Leg Assembly CPR070-00015-DX Belt Pulley Cover Bushing CPR070-00016-DX End Cup Bushing N280-00043-FH Adjustable Washer C CPR070-00010 Flat Key CPR070-00017 Connecting Plate 9206-08000-DX Nylon Lock Nut M8 9301-08000-DX Flat Washer Ø8 9101-08055-DX8.8...