Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Rena Systems TB-390
- Page 1 TB-390 Conveyor Stacker OPERATIONS MANUAL Revised: 7-30-14...
- Page 2 RENA Systems Inc. would like to Thank You for investing in our quality built products. Please record the following information for future reference: Model: Serial Number: Purchase Date: Purchased From: Dealer Name: Contact Name: Address: Address: Phone Number: Please take this opportunity to register your product.
-
Page 3: Specifications
INTRODUCTION The TB-390 conveyor is used to transport media away from the exit end of a printer or tabber and deposit/stack the media into a drop-tray or against an optional back-stop. The stacked media can then be removed, from the back-stop or drop catch tray, without the need to stop the printer or tabber. -
Page 4: Safety Precautions
THIS EQUIPMENT PRESENTS NO PROBLEM WHEN USED PROPERLY. OBSERVE THE FOLLOWING SAFETY RULES WHEN OPERATING THE RENA TB-390 CONVEYOR. BEFORE USING THE TB-390, YOU SHOULD READ THIS MANUAL CAREFULLY AND FOLLOW THE RECOMMENDED PROCEDURES, SAFETY WARNINGS, AND INSTRUCTIONS: Keep hands, hair, and clothing clear of rollers, belts, and other moving parts. -
Page 5: Power Connection
THE LINE CORD. TEST FOR APPROPRIATE TRANSPORT DIRECTION The TB-390 can be configured to run from “right to left” or from “left to right”. 1. Turn on the Power Switch. 2. Turn up the speed control dial, so the transport belts are moving. - Page 6 [A] that mount the cover plate to the conveyor. Do not remove the cover plate. Note: The TB-390 can be configured to run from “right to left” or from “left to right”. The exit end of the conveyor is determined by the direction of the conveyor.
-
Page 7: Positioning The Conveyor
2. Center the conveyor at the exit end of the printer or tabber. Envelope Imager 2.5 and TB-390 Conveyor T-350 Dual Tabber, and TB-390 Conveyor TB-390 Operations Rev. 7/30/2014... -
Page 8: Reverse Operation
When the standard drop-tray is used the media does not need to be overlapped. REVERSE OPERATION The TB-390 can be configured to run from “right to left” or from “left to right”. If the conveyor is not running in the desired direction, it can be reconfigured as follows: 1. -
Page 9: Troubleshooting
Check fuses and breaker on conveyor. Conveyor Won’t Run. Note: Even if the conveyor’s breaker is tripped or the fuses are blown, power is still applied to the “dryer out” outlet when the conveyor’s power switch is on. TB-390 Operations Rev. 7/30/2014... -
Page 10: Optional Accessories
Dryer Mounting Kit (Part #: DKE-700) An optional 700 watt dryer is available for use on the TB-390. To help prevent damage to the conveyor and conveyor belts; the dryer should not be powered on if the conveyor belts are not moving. See the “Safety Precautions” section. - Page 11 [3]. Note: As viewed from operator (front) side of conveyor. Conveyor being used for right to left transport. TB-390 Operations Rev. 7/30/2014...
- Page 12 Bearing Washers are between the support brackets and the cams as shown. Note: Image depicts conveyor being used for right to left transport. NOTE: The Bearing Washers should go between the support brackets and the cams. TB-390 Operations Rev. 7/30/2014...
- Page 13 DO NOT OPERATE THE DRYER IF THE BELTS ON THE CONVEYOR ARE NOT MOVING. DO NOT BLOCK THE EXIT OF THE CONVEYOR WHEN USING THE DRYER. IF A MATERIAL JAM OCCURS; TURN OFF THE CONVEYOR AND DRYER IMMEDIATELY! PLEASE READ THE “SAFETY PRECAUTIONS” SECTION IN THIS MANUAL! TB-390 Operations Rev. 7/30/2014...
- Page 14 Notes TB-390 Operations Rev. 7/30/2014...
- Page 15 © Copyright 2014 NEOPOST USA...
Need help?
Do you have a question about the TB-390 and is the answer not in the manual?
Questions and answers