Brodersen Customer Services Your satisfaction is our primary concern. Here is a guide to Brodersen customer services. To ensure you get the full benefit of our services, please follow the instructions below carefully.
Page 4
Because of Brodersen’s high quality control standards and rigorous testing, most of our customers never need to use our repair service. If a Brodersen product is defective, it will be repaired or replaced at no charge during the warranty period.
A 'Declaration of Conformity' statement to the above standards, and a list of auxiliary equipment used for compliance verification, is available on request. This product must be disposed of in accordance with the WEEE directive. Brodersen A/S, Islevdalvej 187, DK-2610 Roedovre, Denmark, Tel: +45 45 35 26 27, Fax: +45 45 35 26 29, Email: sales@brodersen.com...
8 x digital output Connection: 10 pin removable screw terminals Position: RTU bottom left Available on: 28IO, 42IO and 16DIO versions Brodersen A/S, Islevdalvej 187, DK-2610 Roedovre, Denmark, Tel: +45 45 35 26 27, Fax: +45 45 35 26 29, Email: sales@brodersen.com...
Page 7
Isolation: Input to electronics: at least 350V Channel to channel: at least 350V Available on: 28IO and 42IO versions Brodersen A/S, Islevdalvej 187, DK-2610 Roedovre, Denmark, Tel: +45 45 35 26 27, Fax: +45 45 35 26 29, Email: sales@brodersen.com...
Page 8
I/O ports are shown on the LCD display. The displayed parameter on the LCD can be changed by the keys. Brodersen A/S, Islevdalvej 187, DK-2610 Roedovre, Denmark, Tel: +45 45 35 26 27, Fax: +45 45 35 26 29, Email: sales@brodersen.com...
Page 14
Type of these I/Os are not fixed and could be varied according to the I/O card (I/O plug-in expansion card) version. Brodersen A/S, Islevdalvej 187, DK-2610 Roedovre, Denmark, Tel: +45 45 35 26 27, Fax: +45 45 35 26 29, Email: sales@brodersen.com...
Page 15
Signal Description/Remarks Input / Output Data carrier detect Input Receive data Input Transmit data Output Data terminal ready Output Brodersen A/S, Islevdalvej 187, DK-2610 Roedovre, Denmark, Tel: +45 45 35 26 27, Fax: +45 45 35 26 29, Email: sales@brodersen.com...
Page 16
RJ12 (RJ11) connector. The wiring is according to the following table: Pin no Signal Description/Remarks Input / Output Not used Transmit data Output Signal ground Brodersen A/S, Islevdalvej 187, DK-2610 Roedovre, Denmark, Tel: +45 45 35 26 27, Fax: +45 45 35 26 29, Email: sales@brodersen.com...
Page 17
The online configurator is always updated with the available types of I/O modules. The LB2 series support Hot-Sap and redundant Power supply options for the I/Os. Brodersen A/S, Islevdalvej 187, DK-2610 Roedovre, Denmark, Tel: +45 45 35 26 27, Fax: +45 45 35 26 29, Email: sales@brodersen.com...
NOTE: DO NOT USE STANDARD PATCH OR NETWORK CABLE TO CONNECT I/O MODULES. IT WILL DAMAGE THE LOCALBUS INTERFACES ON BOTH THE RTU AND THE I/O EXPANSION MODULE. ONLY USED UCC-5xx CABLES. Brodersen A/S, Islevdalvej 187, DK-2610 Roedovre, Denmark, Tel: +45 45 35 26 27, Fax: +45 45 35 26 29, Email: sales@brodersen.com...
In the following pictures, some examples of displayed values and statuses on the LCD display are illustrated. Figure 19: Some examples of displayed values and statuses on the LCD Display Brodersen A/S, Islevdalvej 187, DK-2610 Roedovre, Denmark, Tel: +45 45 35 26 27, Fax: +45 45 35 26 29, Email: sales@brodersen.com...
In general we recommend that you keep the RTU32N free from dust and moisture and periodically ensure the all ventilation holes are free and not covered by any means. Brodersen A/S, Islevdalvej 187, DK-2610 Roedovre, Denmark, Tel: +45 45 35 26 27, Fax: +45 45 35 26 29, Email: sales@brodersen.com...
Need help?
Do you have a question about the RTU32N Series and is the answer not in the manual?
Questions and answers