Page 1
medemagruppen P9-0139-B ver. 1.0.2 - August 2015...
Page 2
Medema A/S The latest versions of this user manual are available on our website: www.medema.com. In special cases, for example, important new safety regulations or other significant messages regarding your vehicle, you will be contacted directly by your supplier. User Manual P9-0139-B...
Introduction ................5 Warranty ................. 5 Declaration of conformity ............. 6 Preparation/adjustment ............7 Introduction to the Ergo2 seat ..........9 Extra equipment – contents ..........15 Rear basket ................16 Walking cane holder for back fitting ........17 Lap belt ................... 18 Inertia reel seat belt ...............
Field Safety Notice (FSN) All information concerning safety can be found at www. medema.com, which is always updated with the latest safety information. In the event of important safety-related changes, we will issue an alert (FSN) directly to our customers.
ISO 7176-8. Medema A/S is not liable for any damage or personal injury caused by the unsuitable or unsafe use of the Ergo2 seat. For more information about the use of the Ergo2 seat or this user manual, contact: Medema A/S Tel.: +45 70 10 17 55...
Medema A/S Declaration of conformity Medema A/S hereby declares that: Product: Ergo2 seat Application: (prescribed application in the user manual) Type no.: Ergo2 Type: Class C is CE-marked in accordance with Directive 93/42/EEC of 14 June 1993 concerning medical devices.
Medema A/S Preparation/adjustment Seat height adjustment Loosen the lever for rotating the seat, and turn the seat slightly to the side. Remove the seat by lifting. The seat is very heavy. When lifting the seat, ensure you have the proper lifting posture with your back. A standard seat (45 cm), weighs 27 kg (see below).
Page 8
Medema A/S Unscrew the contra screw. Unscrew the bolt. Use the combination spanner, 17 mm. Adjust the seat post height to the desired position. The seat post is marked with a ring for each centimetre. Tighten the bolt (50 Nm) and then tighten the contra nut (50 Nm).
Medema A/S Introduction to the Ergo2 seat Lever for rotating the seat The lever must be pulled back to rotate the seat. The seat can then be rotated to each side, locking at each 45°. The lever is spring-loaded, and the seat is locked automatically when the lever is released.
Page 10
Medema A/S Seat forward/back lever Pull the lever up to release the seat on the slide rail. The seat can now be moved forward or backward as required, with 200 mm of travel. When the lever is released, the seat will automatically lock into place in the closest stop position.
Page 11
Medema A/S Armrests angle adjustment The armrest can be adjusted 60° by using the adjustment screw. The armrest can be tilted up to facilitate entry and exit. Backrest angle adjustment The backrest can be adjusted 45° backward and 90° forward. To adjust, pull the lever on the right side of the seat.
Page 12
Medema A/S The handle for adjusting the backrest is shown here turned 90° up. Backrest reclined at 45°angle. Backrest inclined forward to 90° angle. This means that the seat does not necessarily need to be removed during transport, e.g. in a car.
Page 13
Medema A/S Backrest forward/back Loosen the specified screws in both sides. 13 mm head. The seat depth can now be adjusted by sliding the backrest forward or back. Shown here with 320 mm seat depth The backrest can be moved backward or forward to the edge of the rail.
Page 14
Medema A/S Headrest height adjustment Press the button in and lower/ raise the headrest as required. Headrest forward/backward adjustment The headrest can be tilted forward and backward as needed. User Manual P9-0139-B User Manual P9-0139-B 14 of 14 14 of 14 Version 1.0.2-2015...
Operating electrical functions ..........34 Seat post system ..............36 Complete seats ..............38 Complete seats with square shaft ........38 Complete seats without headrest ........38 Headrest Ergo2 ..............38 Warning triangle ..............38 User Manual P9-0139-B User Manual P9-0139-B 15 of 39 15 of 39 Version 1.0.2-2015...
Medema A/S Rear basket Fitting basket on the seat (extra equipment) Complete mounting kit for basket. Two brackets and four Allen screws. 4 mm head. Unzip the zip fastener and position the bracket next to the two pre-drilled holes. Fit the basket on the bracket and now it is ready for use.
Medema A/S Walking cane holder for back fitting Walking cane holder, complete set. Zip the zip fastener and securely fit the bracket using two screws. 4 mm head. Bracket fitted. Secure the walking cane holder using two screws. 6 mm head.
Medema A/S Tighten nuts securely on the two screws. 13 mm head. The walking cane holder is now fully fitted. NB: May also be fitted on the left side of the seat, by using the mirror-image bracket. Part number M-127-06-003 Max.
Page 19
Medema A/S Slide in assembly fitting. Re-fit the stop screw. Push the bracket back against the stop screw and tighten securely. 13 mm head. Do this on both sides of the seat. One end of the seat belt is attached to the bracket.
Medema A/S Inertia reel seat belt Remove the stop screw in the rail. 4 mm head. Slide in assembly fitting. Re- fit the stop screw. Push the bracket back against the stop screw and tighten securely. 13 mm head. Screw the seat lock securely to the assembly fitting.
Page 21
Medema A/S Re-tighten the stop screw. The seat belt lock is now fully fitted. Hole for fitting the inertia reel seat belt. Securely screw the inertia reel seat belt in the hole on the back fitting. 13 mm head. Intermediate washer.
Medema A/S Stealth headrest Stealth headrest There are two pre-drilled holes in the back for fitting the headrest (below the cover). Using a pointed tool, feel where the holes are – they can be felt through the cover – and drill carefully through the cover.
Medema A/S The headrest is now fully fitted. The articulated bar's angle can be adjusted and the headrest height can be adjusted. Headrest Stealth Comfort, Adult CR-01396 Headrest Stealth Comfort, Junior CR-01397 Standard armrest Left armrest M-127-07-121 Right armrest M-127-07-120...
Medema A/S Adult armrest Armrest holder, adult, Ergo2, L. M-127-07-169 Armrest holder, adult, Ergo2, R. M-127-07-170 Armrest cushion, MC Ergo standard adult SR-01633 Armrest holder, adult, Ergo2, L. M-127-07-169 Armrest holder, adult, Ergo2, R. M-127-07-170 Armrest cushion, leather cover - 70 x 300 mm R.
Medema A/S Child/Junior armrest Armrest holder, child, Ergo2, L. M-127-07-171 Armrest holder, child, Ergo2, R. M-127-07-172 Armrest cushion, MC Ergo standard child SR-01635 Armrest holder, child, Ergo2, L. M-127-07-171 Armrest holder, child, Ergo2, R. M-127-07-172 Armrest cushion, MC Ergo standard child SR-01635 Armrest cushion, child, leather cover - 70 x 210 mm R.
Medema A/S Hemiplegia armrest Armrest holder, adult, Ergo2, L. M-127-07-169 Armrest holder, adult, Ergo2, R. M-127-07-170 Arm rest, Hemiplegia, right or left side SR-01638 Loosen the two screws before removing the existing armrest. Make angle adjustment using this screw. User Manual P9-0139-B...
Medema A/S Amputated leg rest Amputated leg rest The rail for the amputated leg rest is screwed securely using two screws in the rail below the seat. Fully-fitted amputated leg rest. NB: Can be fitted as mirror- image on opposite side.
Medema A/S Thigh rest Thigh rest Fit the thigh rest using a nut in the rail below the seat. Adjust the thigh rest height, in/out position and angle to suit the user. NB: Can be fitted as mirror- image on opposite side.
Medema A/S Stealth side rest Side rest for fitting to backrest. Stealth swivelling side rest, child 9 x 9, right CR-01382 Stealth swivelling side rest, child 9 x 9, left CR-01383 Stealth swivelling side rest, adult 13 x 18, right...
Medema A/S Electrical Seat front/back position Seat in outer front position. Seat in outer back position. (Can be adjusted 15 cm) Electrical switch to move seat backward/forward. See section "Operating electrical functions". Part number M-127-07-159 User weight 175 kg User Manual P9-0139-B...
Medema A/S Electrical Back Backrest fully reclined. Backrest fully inclined forward. Can be adjusted 15 cm. Electrical switch to incline/ recline backrest. See section "Operating electrical functions". Part number M-127-07-158 User weight 175 kg User Manual P9-0139-B User Manual P9-0139-B...
7° Seat back height: Ergo2 53 cm Height: front edge of seat to road. Ergo2 seat w / slide 66,5 - 76,5 cm Height: footplate to front edge of seat. Ergo2 seat w / slide 47,5 - 57,5 cm The backrest angle: Ergo2 Ca.
7° Seat back height: Ergo2 53 cm Height: front edge of seat to road. Ergo2 seat w / slide 64 - 74 cm Height: footplate to front edge of seat. Ergo2 seat w / slide 45 - 55 cm The backrest angle: Ergo2 Ca.
Medema A/S Operating electrical functions All of the electrical functions are fitted as standard equipment with a control unit for single function. If two electrical functions are chosen, a unit is fitted under each armrest. If three or four electrical functions are desired, one or two double control units must be purchased.
Page 35
PCB or PCB, since the entire system is controlled via the joystick. Seat weight Seat model Weight Ergo2 seat 40 cm 26 kg Ergo2 seat 45 cm 27 kg Ergo2 seat 50 cm...
Medema A/S Seat post system As standard, the Ergo2 seat system is equipped with a height- adjustable seat post, which requires a tool to adjust. When it is tightened, it is completely fixed. Seat post - fixed. M-127-02-012 Alternatively, the seat post can be supplied with a positioning bolt solution.
Page 37
Medema A/S Plastic washer. M-127-7-234 (converting from Ergo2 to Ergo1/Eblo) Loose seat post square. M-127-2-562. Loose seat post for T model. M-127-2-588. User Manual P9-0139-B User Manual P9-0139-B 37 of 39 37 of 39 Version 1.0.2-2015 Version 1.0.2-2015...
M-127-07-152 SEAT MC ERGO2 45 CM, COMPLETE M-127-07-153 SEAT MC ERGO2 50 CM, COMPLETE M-127-07-154 Complete seats with square shaft SEAT MC ERGO2 40 CM, COMPLETE WITH SQUARE M-127-07-152F SHAFT SEAT MC ERGO2 45 CM, COMPLETE WITH SQUARE M-127-07-153F SHAFT...