Page 1
GX630 (MS-1652)Disassemble SOP ■ 1、Battery Pack ■ 2、BOTTOM DOOR ASSY ■ 3、THERMAL-KIT And CPU Module ■ 4、RAM、WLAN And TUNER Module ■ 5、HDD Module ASSY ■ 6、ODD Module ASSY ■ 7、HINGE COVER ASSY ■ 8、UP CASE ASSY ■ 9、LOWER CASE ASSY...
Page 2
GX630(MS-1652)Disassemble SOP ■ 1、Battery Pack 1-1: Push the battery Unlock button as below; 1-2: Push the battery Release button as below, then slide the battery pack out of the slot; Part Name Part No. Battery Pack S9N-0366200-SB3...
Page 3
GX630(MS-1652)Disassemble SOP ■ 2、BOTTOM DOOR ASSY 2-1: Remove 2pcs M2.5*5mm Screws ; Note:Screw driver torque is 2.0~2.5kgf.cm 2-2: Remove Bottom Door Assy as below;...
Page 4
GX630(MS-1652)Disassemble SOP 2-3: Remove SIM Card Door as below; Part Name Part No. Screw E43-1255001-G68 SIM CARD DOOR E2P-6510511-Y31 BOTTOM DOOR ASSY 307-651J411-Y31...
Page 5
GX630(MS-1652)Disassemble SOP ■ 3、THERMAL-KIT And CPU Module 3-1: Remove 7pcs SPING Screws and 2pcs M2.5*5mm screws, Then Disconnect CPU Fan sink Cable; Note:Screw driver torque is 2.0~2.5kgf.cm 3-2: Remove CPU Fansink; Part Name Part No. screw E43-1255001-G68 CPU FANSINK E32-1300112-F05...
Page 6
GX630(MS-1652)Disassemble SOP 3-3: Open CPU lock as below; 3-4: Remove CPU Module; Part Name Part No. CPU Module A10-K82G2F6-A08...
Page 7
GX630(MS-1652) Disassemble SOP 3-5: Remove 2pcs M2.5*5mm Screws; Note:Screw driver torque is 1.8~2.0kgf.cm 3-6: Remove VGA Card Module; Part Name Part No. VGA CARD Module 602-V114-020 Screw E43-1255001-G68...
Page 8
GX630(MS-1652)Disassemble SOP ■ 4、RAM、WLAN And TUNER Module 4-1: Push RAM Slot Fastener as below; 4-2: Remove RAM Module; Part Name Part No. RAM Module S7C-S357701-T10...
Page 9
GX630(MS-1652)Disassemble SOP 4-3: Remove WLAN Card Antenna, Then Remove 1pcs M2*3mm Screw; Note:Screw driver torque is 1.5~2.0kgf.cm 4-4: Remove WLAN Card Module; Part Name Part No. WLAN CARD Module S57-3800010-T46 Screw E43-1203007-G68...
Page 10
GX630(MS-1652)Disassemble SOP 4-5: Remove Tuner Antenna, Then Remove 1pcs M2*3mm; Note:Screw driver torque is 1.5~2.0kgf.cm 4-6: Remove Tuner Module; Part Name Part No. TUNER Module S36-0000610-K45 Screw E43-1203007-G68...
Page 11
GX630(MS-1652)Disassemble SOP ■ 5、HDD Module ASSY 5-1: Remove 2pcs M2.5*5mm Screws Then Remove HDD Door Assy as below; Note:Screw driver torque is 2.0~2.5kgf.cm Part Name Part No. Screw E43-1255001-G68 HDD DOOR ASSY 307-651K411-Y31...
Page 12
GX630(MS-1652)Disassemble SOP 5-2: Remove HDD Module as below; Part Name Part No. Screw E43-1255001-G68...
Page 13
GX630(MS-1652)Disassemble SOP 5-3: Remove 2pcs M3*3.5mm Screws Then Remove HDD Bracket as below; Note:Screw driver torque is 2.0~2.5kgf.cm Part Name Part No. Screw E43-1303501-G68 HDD Bracket E2M-6510311-Y28 HDD MODULE ASSY S71-2416504-T14...
Page 14
GX630(MS-1652)Disassemble SOP ■ 6、ODD Module ASSY 6-1: Remove 1pcs M2.5*5mm Screw Then Remove ODD Module Assy as below; Note:Screw driver torque is 2.0~2.5kgf.cm Part Name Part No. Screw E43-1255001-G68...
Page 15
GX630(MS-1652)Disassemble SOP 6-2: Remove ODD Bezel as below; Part Name Part No. ODD Bezel E2P-651F211-Y31...
GX630(MS-1652)Disassemble SOP 6-3: Remove 2pcs M2*3mm Screws Then Remove ODD Bracket as below; Note:Screw driver torque is 1.5~1.8kgf.cm Part Name Part No. Screw E43-1203007-G68 ODD MODULE S7D-2270001-SI4 ODD Bracket E2M-6510211-Y28...
GX630(MS-1652)Disassemble SOP 7-3: Remove Hinge Cover Cable as below; Part Name Part No. POWER BOARD 607-1652B-01S...
Page 20
GX630(MS-1652)Disassemble SOP 7-4: Remove Cap Sensor Board as below;...
Page 21
GX630(MS-1652)Disassemble SOP 7-5: Remove Cap Sensor Board as below; Part Name Part No. Cap Sensor Board 607-1652D-01S Cap Sensor Board Cable K1C-1012023-J36...
Page 22
GX630(MS-1652)Disassemble SOP 7-6: Disconnect Camera Cable out of the slot as below; Part Name Part No. Camera Cable K10-3006056-H39...
Page 23
GX630(MS-1652)Disassemble SOP 7-7: Remove 2pcs M2.5*5mm Screw; Note:Screw driver torque is 2.0~2.5kgf.cm 7-8: Use Plastic Stick Push Hinge Cap as below; Part Name Part No. Screw E43-1255001-G68 Hinge Cap_L E2P-6513211-Y31 Hinge Cap_R E2P-6513311-Y31...
Page 24
GX630(MS-1652)Disassemble SOP 7-9: Draw Out Camera Cable、Wireless Antenna and 3G Antenna as below; Part Name Part No. 3G Antenna S79-1800780-V03 Wireless Antenna_L S79-1800800-V03 Wireless Antenna_R S79-1800790-V03...
Page 25
GX630(MS-1652)Disassemble SOP 7-10: Disconnect Coaxia Cable as below; Part Name Part No. Coaxia Cable K19-3040006-H39...
Page 26
GX630(MS-1652)Disassemble SOP 7-11: Remove 4pcs M2.5*7mm Screws; then remove LCD MOUDLE. Note:Screw driver torque is 3.5±0.2kgf.cm(1-2) Note:Screw driver torque is 3.0-3.5kgf.cm(3-4) Part Name Part No. Screw E43-1257001-H29...
Page 27
GX630(MS-1652)Disassemble SOP ■ 8、UPCASE ASSY 8-1: Remove 5pcs M2*3mm Screws, Then Remove Keyboard as below; Note:Screw driver torque is 1.5~2.0kgf.cm Part Name Part No. Screw E43-1203007-G68 Keyboard S1N-3UUS112-C54...
Page 28
GX630(MS-1652)Disassemble SOP 8-2: Remove 2pcs M2*3mm Screws, Then Remove Power Board as below; Note:Screw driver torque is 1.5~2.0kgf.cm Part Name Part No. Screw E43-1203007-G68 Power Board 607-1652B-01S...
Page 29
GX630(MS-1652)Disassemble SOP 8-3: Remove 13pcs M2.5*5mm Screws; Note:Screw driver torque is 2.0~2.5kgf.cm Part Name Part No. Screw E43-1255001-G68...
Page 30
GX630(MS-1652)Disassemble SOP 8-4: Remove PCI-E Card And XD Card as below; Part Name Part No. PCI-E Card E2P-6510411-Y31 XD Card E2M-6510111-A81...
Page 31
GX630(MS-1652)Disassemble SOP 8-5: Disconnect Speaker Cable and Microphone Cable as below; Part Name Part No. Speaker S33-A020200-F33 Microphone S34-2100580-F33...
Page 32
GX630(MS-1652)Disassemble SOP 8-6: Remove FFC Cable(TO Power Board) and FFC Cable(TO T/P) as below; Part Name Part No. FFC Cable(Power Board) K1C-1018003-J36 FFC Cable(T/P) K1C-1012024-J36...
Page 33
GX630(MS-1652)Disassemble SOP 8-7: Remove 2pcs M2*3mm Screws, Then Remover FFC Cable(TO M/B)&(TO Button) as below; Note:Screw driver torque is 1.5~2.0kgf.cm 8-8: Remove Touchpad Bracket; Part Name Part No. Screw E43-1203007-G68 FFC Cable(TO Button) K1C-1012025-J36 Touchpad Bracket E2M-5222911-G40...
Page 34
GX630(MS-1652)Disassemble SOP 8-9: Remove 1pcs M2*3mm Screw, Then Remove Touchpad Button Board; Note:Screw driver torque is 1.0~1.5kgf.cm Part Name Part No. Screw E43-1203007-G68 Touchpad Button Board 607-1651C-C10...
Page 35
GX630(MS-1652)Disassemble SOP 8-10: Remove FFC Cable (TO Button) as below, then remove touchpad module; Part Name Part No. FFC Cable(TO Button) K1C-1012025-J36 Touchpad Module S78-3700360-SD2...
Page 36
GX630(MS-1652)Disassemble SOP 8-11: Remove 4pcs M2*3mm screws, then remove speaker module s below; Note:Screw driver torque is 1.0~1.5kgf.cm 8-12: Remove 2pcs s below; Part Name Part No. screw E43-1203007-G68 speaker S33-A020200-F33 magnet E2Y-6512511-SF7...
Page 37
GX630(MS-1652)Disassemble SOP ■ 9、LOWER CASE ASSY 9-1: Remove 1pcs M2.5*5mm Screw, Then Remove FFC Cable (TO Audio Board) as below; Note:Screw driver torque is 2.3±0.2kgf.cm 9-2: Remove FFC Cable (TO Power Board) as below; Part Name Part No. Screw E43-1255001-G68...
GX630(MS-1652)Disassemble SOP 9-3: Remove RJ11 Cable and Bluetooth Cable as below; 9-4: Remove M/B; Part Name Part No. RJ11 CABLE K10-3002114-H58 BLUETOOTH CABLE K10-3008077-H39 607-16521-01S...
Page 39
GX630(MS-1652)Disassemble SOP 9-5: Remove 1pcs M2*3mm Screw, Then Remove Bluetooth Antenna; Note:Screw driver torque is 1.0~1.5kgf.cm Part Name Part No. Screw E43-1203007-G68 BLUETOOTH ANTENNA S79-1800890-V03 BLUETOOTH MODULE 605-6837D-070...
Page 40
GX630(MS-1652)Disassemble SOP 9-6: Remove 2pcs M2*3mm Screws, Then Remove Audio Board; Note:Screw driver torque is 1.0~1.5kgf.cm Part Name Part No. Screw E43-1203007-G68 AUDIO BOARD 607-1652A-01S LOWER CASE ASSY 307-651D411-Y31...
Page 41
GX630(MS-1652)Disassemble SOP 9-7: Remove Bluetooth Antenna、RJ11 Cable and TV IO Jack; Part Name Part No. BLUETOOTH ANTENNA S79-1800890-V03 RJ11 CABLE K10-3002114-H58 TV IO JACK K19-3001017-H39...
Page 42
GX630(MS-1652)Disassemble SOP ■ 10、LCD MODULE ASSY 10-1: Remove 8pcs LCD Rubbers Then Remove 8pcs M2.5*5mm Screws; Note:Screw driver torque is 2.0~2.5kgf.cm Part Name Part No. LCD Rubber E2Y-6510121-Y40 Screw E43-1255001-G68...
GX630(MS-1652)Disassemble SOP 10-2: Remove LCD Bezel as below; Part Name Part No. LCD BEZEL 307-651B211-Y31...
Page 44
GX630(MS-1652)Disassemble SOP 10-3: Remove 8pcs M2.5*5mm Screws, Then Remove Left And Right Hinge; Note:Screw driver torque is 2.0~2.5kgf.cm Part Name Part No. Screw E43-1255001-G68 Hinge_Left E2M-6510411-G60 Hinge_Right E2M-6510711-G60...
Page 45
GX630(MS-1652)Disassemble SOP 10-4: Remove Inverter Cable, Then Remove Display Module; 10-5: Remove 2pcs MAGNET as below; Part Name Part No. MAGNET E2Y-3110411-SF7...
Page 46
GX630(MS-1652)Disassemble SOP 10-6: Remove Inverter Module、3G Antenna、WLAN Antenna; Part Name Part No. INVERTER S78-3300450-SG3 Wireless Antenna_R S79-1800790-V03 Wireless Antenna_L S79-1800800-V03 3G Antenna S79-1800780-V03...
Page 47
GX630(MS-1652)Disassemble SOP 10-7: Remove CMOS Camera Module as below; Part Name Part No. CMOS Camera Module S1F-0003040-C54 Camera Cable K10-3006056-H39 LCD Cover Assy 307-651A511-CG0...
Page 48
GX630(MS-1652)Disassemble SOP 10-8: Remove Coaxial Cable as below; Part Name Part No. Coaxial Cable K19-3040006-H39 Display Module S1J-640G017-S02...
Page 49
GX630(MS-1652)Disassemble SOP 10-9: Remove 8pcs M2*3mm Screws, Then Remove LCD Bracket as below; Note:Screw driver torque is 1.5~2.0kgf.cm Part Name Part No. Screw E43-1203007-G68 LCD Bracket_Left E2M-6510511-Y28 LCD Bracket_Right E2M-6510611-Y28...
Page 50
GX630 (MS-1652)screws specification Photo Screw specification Label (M2.5*L5MM) black (M2*L3MM)white (M3*L3.5MM) white (M2.5*L7MM) black...
Page 51
GX630 (MS-1652)screws specification ■ 1、BOTTOM DOOR ASSY total 20pcs screws, ■ specification: Photo Screw specification label (M2.5*L7MM) black (M2.5*L5MM) black...