Table of Contents
Advertisement
Quick Links
A MIDDLEBY COMPANY
These instructions should be read thoroughly before attempting installation. Set up, installation
and Performance Check should be performed by a qualified service technician. The
Manufacturer, Southbend (1100 Old Honeycutt Rd., Fuquay-Varina, North Carolina 27526),
informs you that unless the installation instructions for the above described Southbend product
are followed and performed by a qualified service technician, (a person experienced in and
knowledgeable concerning the installation of commercial gas and/or electrical cooking
equipment) then the terms and conditions of the Manufacturer's Limited Warranty will be
rendered void and no warranty of any kind shall apply.
If the equipment has been changed, altered, modified or repaired by other than a qualified
service technician during or after the 12-month limited warranty period, then the manufacturer
shall not be liable for any incidental or consequential damages to any person or to any property
which may result from the use of the equipment thereafter. Some States do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion thereto may not apply to you.
In the event you have any question concerning the installation, use, care, or service of the
product, write Customer Service Department, Southbend Corporation, 1100 Old Honeycutt Rd.,
Fuquay-Varina, North Carolina 27526.
$4.00
southbend
OWNER'S MANUAL
INSTALLATION
USER'S GUIDE
SERVICE
PARTS
GAS TILTING
BRAISING PAN
MODELS:
BPG-40-M
BPG-40-M-9
7" PAN
9" PAN
GAS TILTING BRAISING PANS
(Manual Section BP)
Advertisement
Table of Contents
Summary of Contents for Middleby Southbend BPG-40-M
- Page 1 A MIDDLEBY COMPANY OWNER'S MANUAL INSTALLATION USER'S GUIDE SERVICE PARTS GAS TILTING BRAISING PAN MODELS: BPG-40-M 7" PAN BPG-40-M-9 9" PAN These instructions should be read thoroughly before attempting installation. Set up, installation and Performance Check should be performed by a qualified service technician. The Manufacturer, Southbend (1100 Old Honeycutt Rd., Fuquay-Varina, North Carolina 27526),...
-
Page 2: Table Of Contents
IN THE EVENT A GAS ODOR IS DETECTED, SHUT DOWN EQUIPMENT AT THE MAIN SHUTOFF VALVE AND CONTACT THE LOCAL GAS COMPANY OR GAS SUPPLIER FOR SERVICE. southbend 1100 Old Honeycutt Road Fuquay-Vanna. NC 27526 A MIDDLEBY COMPANY (919) 552-9161 FAX (919) 552-9798 (800) 348-2558... -
Page 3: Section One - Installation
GAS TILTING BRAISING PANS INSTALLATION SPECIFICATIONS NUMBER ORIFICE MANIFOLD ITEM RATE EACH TOTAL RATE PRESSURE TYPE PER UNIT SIZE Natural 4" W.C. 8,500 BTU/Hr. 85,000 BTU/Hr. #55 .055" Dia. MAIN BURNERS 10" W.C. 8,500 BTU/Hr. 85,000 BTU/Hr. #66 .035" Dia. Natural 4"... - Page 4 INSTALLATION GENERAL: The installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1-1984, and with the National Electrical Code ANSI NFPA 70-1984. These models are design certified for operation on natural or propane gases. The serial plate is located just inside the cabinet door, at the left front of the cabinet bottom.
- Page 5 INSTALLATION LEGS OR OPTIONAL CASTERS: Braising pans are shipped completely assembled with the exception of the legs. A set of 6" legs is packed in the drain container. A threaded receptacle is fastened to the base frame at each corner. Each leg has a similar mating thread. Raise unit sufficiently to allow legs to be screwed into the receptacles.
- Page 6 INSTALLATION LIGHTING: Open compartment door. Manual gas valve must be "OPEN." The screws and the right angle shield assemblies at the rear of the burner compartment are for shipping purposes only and must be removed prior to initially lighting the unit. Turn thermostat to "OFF."...
-
Page 7: Warranty
GAS TILTING BRAISING PAN USER'S GUIDE LIMITED WARRANTY Southbend warrants that the equipment, as supplied by the factory to the original purchasers, is free from defects in materials and workmanship. Should any part thereof become defective as a result of normal use within the period and limits defined below, then at the option of Southbend such parts will be repaired or replaced by Southbend or its Authorized Service Agency. -
Page 8: Operation
OPERATION THERMOSTAT: The thermostat controls the operation of the burners. Set the thermostat to the desired temperature. The burners will come on until the thermostat is satisfied. They will cycle "ON" and "OFF" to maintain this temperature. Turn the thermostat to the "OFF" position to shut down the braising pan. TIMER: Turn the dial beyond five minutes and then set for the desired time. -
Page 9: Maintenance
MAINTENANCE WARNING: ALL ADJUSTING AND SERVICE SHOULD BE PERFORMED BY A PERSON KNOWLEDGEABLE IN MAKING SUCH ADJUSTMENTS. IF IN DOUBT - CALL YOUR AUTHORIZED SERVICE AGENCY. Following daily and periodic maintenance procedures will enhance long-life for your equipment. Climatic conditions —... - Page 10 MAINTENANCE PAN: Because your Braising Pan is in use for a wide variety of foods — for breakfast, lunch and dinner service — clean it as soon as possible after each use. Before starting to clean, make sure that gas is OFF; then follow this recommended procedure: Flush the pan thoroughly with lukewarm water, then drain —...
- Page 11 MAINTENANCE Part No. Description 1163453 Upper Drive Shaft 1056700 Bearing for rod - 2-piece 1058500 Thrust Washers - 2-piece 1041200 Spring Pin - Holds crank wheel on shaft COMPOSITE SKETCH SHOWING PARTS OF BOTH HAND & POWER LIFTS BRAISING PAN MECHANISM DRG. NO. 1074101 GAS TILTING BRAISING PANS SECTION TWO —...
- Page 12 MAINTENANCE BRAISING PAN LID MECHANISM DRG NO. 1074102 GAS TILTING BRAISING PANS SECTION TWO — USER'S GUIDE Litho in U.S.A. PAGE 6 8-88...
-
Page 13: Section Three - Service
GAS TILTING BRAISING PAN SERVICE ADJUSTMENTS WARNING: AT LEAST TWICE A YEAR HAVE YOUR SOUTHBEND AUTHORIZED SERVICE AGENCY CLEAN AND ADJUST THE UNIT FOR MAXIMUM PERFORMANCE. All units are adjusted at the factory. In case of problems in operation at initial installation, check type of gas and manifold pressure and compare with information listed on the serial plate. - Page 14 ADJUSTMENTS PRESSURE REGULATOR: The pressure regulator is factory set at 4" W.C. for natural gas and 10" W.C. for LP gas. To check the manifold pressure: Turn thermostat "OFF" and Unitrol knob to "PILOT" setting. Remove pressure tap plug from outlet side of Unitrol body (see diagram page 4, this Section). Install a fitting appropriate to connect a manometer.
-
Page 15: Troubleshooting
SERVICE TROUBLE SHOOTING: Problem Look for — Burners do not come on gas supply to unit off. manual gas valve in unit off. Unitrol in "OFF" or "PILOT" position. pilot not ignited. - thermostat not "ON." pan not in lowest position. Pilot will not stay ignited Unitrol in "OFF"... - Page 16 SERVICE GAS TILTING BRAISING PANS SECTION THREE — SERVICE Litho in U.S.A. 8-88 PAGE 4...
-
Page 17: Section Four - Parts
GAS TILTING BRAISING PAN PARTS PARTS WARNING: INSTALLATION OF OTHER THAN GENUINE SOUTHBEND PARTS WILL VOID THE WARRANTY ON THIS EQUIPMENT. The serial plate is located inside the cabinet on the bottom, at the left edge. An "E" suffix at the end of the model number indicates the unit is equipped with electronic ignition. - Page 18 1100 Old Honeycutt A MIDDLEBY COMPANY Road Fuquay-Varina, NC 27526 (919) 552-9161 FAX (919) 552-9798 (800) 348-2558 Convection ovens Fryers Cooker/mixer kettles Cook & hold convection ovens Special & custom equipment Floor model broilers Bake & roast ovens Convection steamers...
- Page 19 Southbend Authorized Service Agency, or your dealer. To avoid confusion, always refer to the model number, serial number, and type of your unit. southbend 1100 Old Honeycutt A MIDDLEBY COMPANY Fuquay-Varina. NC (919) 552-9161 FAX (919) 552-9798 (800) 348-2556 Litho in U.S.A.
Need help?
Do you have a question about the Southbend BPG-40-M and is the answer not in the manual?
Questions and answers