Subscribe to Our Youtube Channel
Related Manuals for Cedes CabSafe 3D
Summary of Contents for Cedes CabSafe 3D
- Page 1 CabSafe 3D Sensor & Controller Installation and Operation Manual CEDES AG is certified according to ISO 9001: 2015 English Pages 2 - 14 115 944 en | 200820 | V1.0...
-
Page 2: Table Of Contents
Switzerland 6.4.1 Non-intended use ......... 18 6.4.2 Hazards of laser radiation ......18 6.5 Installation CabSafe 3D sensor ....18 © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 2/28... -
Page 3: Safety Information
Disregarding these warnings can result in Intended use injury. The CabSafe 3D Time-of-Flight (TOF) sensor, the ce- gard/Pro (CabSafe 2D) light curtain, and the CabSafe © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 3/28... -
Page 4: Introduction Cabsafe System
Depending on an internal sequencing, the CabSafe Controller either holds the door open, allows it to reverse or allows it to close. © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 4/28... -
Page 5: General Operation
© CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 5/28... -
Page 6: Features
WAGO plug, guide the cable through CabSafe Controller itself (only DIP switch set- the grommet, reconnect the WAGO plug tings). © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 6/28... -
Page 7: Electrical Connection
Figure 5: Electrical connections CabSafe Controller with push pull output Details for the door position signal/switch are provided in chapter 5.7. connection push-pull output schematically described in Figure 6: © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 7/28... -
Page 8: Door Position Signal
5.8.2. Table 3: Definition of how the door closing or door closed is detected (*= factory default) Notice: © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 8/28... -
Page 9: Settings For The Door Opening Height
CabSafe 3D sensor 3D-time (see chapter 4.2) 20 sec Table 8: Descriptions of the times provided in Figure 8 © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 9/28... -
Page 10: Controller Output Logic
(walking speed between 0.3 m/s and 1.0 m/s). The CabSafe 3D sensor must signal object detected at all tests. © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 10/28... - Page 11 Flash = 300 ms On / 300 ms Off CabSafe 2D light curtain (LC) Pause = 1’800 ms Table 10: Description status LEDs © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 11/28...
-
Page 12: Trouble Shooting
(200417), manufacturing job number (00654321), employee number responsible for final test (01234), and incremental count (000048) build the lot number. © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 12/28... -
Page 13: Maintenance
CabSafe Controller. 3000 Figure 12: Dimensions door position sensor © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 13/28... - Page 14 The cable outlet of the sensor must always be positioned towards the door opening direction at the installed door as indicated in Figure 14. It is only one switch required per elevator (for central and for side opening). © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 14/28...
-
Page 15: Technical Data Cabsafe Controller
Typical system response time CabSafe 3D < 250 ms CabSafe 2D < 20 ms + response time CabSafe light curtain Table 19 © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 15/28... -
Page 16: Connectors
50 (1.97 in.) 66.28 (2.69 in.) (64.5) Side view PCB PCB on adapter Figure 15: Dimensions CabSafe Controller PCB solutions © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 16/28... -
Page 17: Dimensions Box Solution
Center (future) Right (future) Example: Figure 17: Principal installation of a CabSafe 3D sensor (example CabSafe 3D-F for side opening) © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 17/28... -
Page 18: Safety Information
6.5.1.2 Glass door elevators For elevators with glass doors the following requirements must be considered in addition to chapter 6.5.1.1: © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 18/28... -
Page 19: Mechanical Installation
Figure 20: Mounting location and orientation – right side opening ► Do not overtighten the mounting screws. door ► Mount the brackets on a flat surface © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 19/28... -
Page 20: 3Mounting Distance To The Door
Figure 25 for thin transoms (< 2 mm [0.079 in.]) available Back transom mount- Mainly for modernization Table 22: Mounting hardware © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 20/28... -
Page 21: 1Dimensions Flush Mounting Bracket
For the two screws holes a diameter (“d”) of 4.5 mm mm (0.0787 in.). (0.177 in.; 3/17”) shall be used if the sensor is © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 21/28... -
Page 22: 4Back Transom Mounting
(see chapter 5.8.1). The 3D detection field fulfills the approaching object requirements specified in ASME A17.1-2019 / CSA B44:19 as shown in Figure 31 below. © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 22/28... - Page 23 For elevator banks that have elevators that face each other, interference between approaching object sensors can occur. To prevent such interference, the operation frequency of the CabSafe 3D sensor should be configured using DIP11 on the CabSafe Controller (see chapter 5.8.6) For example, Figure 32 shows a bank of elevators where there are three elevators on one side of a hallway and three elevators on the opposite side of the hallway.
-
Page 24: Timing Diagram
< 5 s Typical response time <250 ms Release time Min. 1.5 s Table 23: Descriptions for the timings in Figure 33 © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 24/28... -
Page 25: Start-Up Cabsafe 3D
4 flash, 1 Internal sensor error, pause replace sensor 6 flash, 1 Communication problem pause Table 25: Error code description © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 25/28... -
Page 26: Product Label
-40°C … +85°C (-4°F … 185°F) Max. ambient light 50’000 Lux Table 29 Figure 34: Product labels CabSafe 3D sensor © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 26/28... -
Page 27: Operation Characteristics
Wires AWG26 brown blue GND (0V) black Communication (RS485) white Communication (RS485) gray Communication (RS485) green Communication (RS485) Table 31 © CEDES | V 1.0 CEDES AG reserves the right to modify or change technical data without prior notice. 27/28... -
Page 28: Dimensions Cabsafe 3D Sensor
Equipment (WEEE): At the end of life, this equipment should be collected separately from any unsorted municipal waste. CEDES AG, Science Park | CH-7302 Landquart Phone: +41 81 307 2323 | Fax: +41 81 307 2325 | info@cedes.com | www.cedes.com...
Need help?
Do you have a question about the CabSafe 3D and is the answer not in the manual?
Questions and answers