Related Manuals for Avago Emulex OCe14000B Series
Summary of Contents for Avago Emulex OCe14000B Series
- Page 1 OneConnect OCe14000B-series Adapters Installation Manual pub-005129 Rev. A Connect • Monitor • Manage...
- Page 2 Copyright © 2013–2015 Emulex. All rights reserved worldwide. No part of this document may be reproduced by any means or translated to any electronic medium without the prior written consent of Emulex. Information furnished by Emulex is believed to be accurate and reliable. However, no responsibility is assumed by Emulex for its use;...
-
Page 3: Table Of Contents
Table of Contents Table of Contents List of Figures ..................5 List of Tables ..................6 1. Introduction ..................7 Features....................10 General Features.................10 OCe14101B Adapters ................11 OCe14102B Adapters ................11 OCe14104B Adapters ................11 OCe14401B Adapters ................11 Protocol-Specific Capabilities..............12 Adapter Identification................ - Page 4 Table of Contents Laser Safety Notice ................. 34 OneConnect OCe14000B-series Adapters Installation Manual pub-005129 Rev. A...
-
Page 5: List Of Figures
List of Figures List of Figures Figure 1-1 Emulex OCe14102B Adapter ........... 9 Figure 1-2 Emulex OCe14102B-NT/UT Adapter.......... 9 Figure 1-3 Emulex OCe14401B Adapter ..........10 Figure 2-1 Optical Transceiver Example..........16 Figure 2-2 Releasing the Latch on an Optical Transceiver......17 Figure 2-3 Removing the Bracket ............17 Figure 2-4 Secure Firmware Jumper Location J3 on... -
Page 6: List Of Tables
List of Tables List of Tables Table 1-1 OCe14000B-series Adapters ........... 7 Table 3-1 OCe14101B-NX, OCe14102B-NX/-UX, and OCe14104B-NX/-UX Cable and Connector Specifications ........21 Table 3-2 OCe14401B-NX/-UX Cable and Connector Specifications ....21 Table 3-3 OCe14101B-NX, OCe14102B-NX, and OCe14104B-NX/-UX Adapter Emulex OneConnect Accessories ..........23 Table 3-4 OCe14401B-NX/UX Adapter Emulex OneConnect Accessories...23 Table 3-5... -
Page 7: Introduction
1. Introduction 1. Introduction ® ® This manual describes the following Emulex OneConnect OCe14000B-series of multi-protocol Peripheral Component Interconnect Express (PCIe) adapters that provide Ethernet networking, RDMA over Converged Ethernet (RoCE), internet Small Computer System Interface (iSCSI) functionality, and Fibre Channel over Ethernet (FCoE) functionality for convergence of Fibre Channel (FC) traffic onto a Ethernet fabric. - Page 8 1. Introduction Table 1-1 OCe14000B-series Adapters (Continued) Adapter Number of Supported Models Ports Protocols Cable Type OCe14104B-NX 4x10GbE 10GbE SFP+ Passive DAC Cable RoCE 10GbE SFP+ Active DAC Cable 10GbE SFP+ AOC Cable OCe14104B-UX 4x10GbE RoCE iSCSI FCoE OCe14104B-NM 4x10GbE 10GbE SFP+ fiber optic cable with LC connector RoCE OCe14104B-UM...
-
Page 9: Figure 1-1 Emulex Oce14102B Adapter
1. Introduction Note: The illustrations in this manual are only examples. The actual hardware may vary. Figure 1-1 Emulex OCe14102B Adapter Figure 1-2 Emulex OCe14102B-NT/UT Adapter OneConnect OCe14000B-series Adapters Installation Manual pub-005129 Rev. A... -
Page 10: Features
1. Introduction Features Figure 1-3 Emulex OCe14401B Adapter Features General Features Eight-lane (x8) Generation 3 PCIe interface at 8GTps, 5GTps, or 2.5GTps (auto-negotiated with system) Parts and construction are compliant to the European Union Directive of RoHS, and similar regulatory requirements for other countries Standard, full height I/O bracket is factory-installed. -
Page 11: Oce14101B Adapters
1. Introduction Features As supported, a comprehensive array of NIC, iSCSI, FCoE, operating system drivers, including support for Windows, Linux, VMware, and Solaris. As supported, Unified Ethernet-to-FC SAN connectivity provided by an FCoE switch. OCe14101B Adapters Up to eight PCIe functions per adapter, individually configurable to NIC and ... -
Page 12: Protocol-Specific Capabilities
1. Introduction Features Protocol-Specific Capabilities NIC capabilities include NDIS 5.2, 6.0, and 6.2-compliant Ethernet functionality IPv4/IPv6 TCP, UDP checksum offload IPv4/IPv6 receive-side scaling (RSS) IPv4/IPv6 large receive offload (LRO) IPv4/IPv6 large segment offload (LSO) Programmable MAC addresses ... -
Page 13: Adapter Identification
1. Introduction Adapter Identification Low latency queues for small packet sends and receives Windows Server SMB Direct (SMB over RDMA) Adapter Identification Each adapter has several identification numbers. Emulex recommends recording these numbers before installation. Institute of Electrical and Electronics Engineers (IEEE) address – a unique 64-bit ... - Page 14 1. Introduction Abbreviations iSCSI Internet Small Computer System Interface Lucent connector light-emitting diode large receive offload large segment offload Media Access Control Mbit megabit millimeters NDIS Network Driver Interface Specification network interface card NPIV N_Port ID Virtualization OFED OpenFabrics Enterprise Distribution PCBA printed circuit board assembly PCIe...
- Page 15 1. Introduction Abbreviations vital product data World Wide Name OneConnect OCe14000B-series Adapters Installation Manual pub-005129 Rev. A...
-
Page 16: Installation
2. Installation Preparing the Adapter for Installation 2. Installation This section provides information on changing from the adapter bracket from a standard bracket to a low-profile adapter bracket, and installing the adapter in a computer. Preparing the Adapter for Installation Before installing the adapter, you may need to perform one or both of the following procedures: Change the bracket from a full-height to the low-profile version by following... -
Page 17: Figure 2-2 Releasing The Latch On An Optical Transceiver
2. Installation Preparing the Adapter for Installation 2. To remove a transceiver, pull the bail (handle) out and down to release the latch, and gently pull the transceiver from its cage. Be careful not to force the transceiver from the cage. Figure 2-2 shows a transceiver with the latch released (bail extended) and another transceiver latched in place. -
Page 18: Enabling Or Disabling The Secure Firmware Feature
2. Installation Preparing the Adapter for Installation Enabling or Disabling the Secure Firmware Feature Some OCe14000B-series adapters have a jumper that enables or disables the Secure Firmware feature as required. To ensure that the firmware on this adapter cannot be changed offline (using an ISO flash file), leave the jumper block installed on the relevant jumper pins (Secure Firmware enabled). -
Page 19: Figure 2-5 Secure Firmware Jumper Location J6 On Oce14104B-Series
2. Installation Preparing the Adapter for Installation To disable Secure Firmware, remove the jumper from J6 Header J6 with jumper installed (Secure Firmware enabled) Figure 2-5 Secure Firmware Jumper Location J6 on OCe14104B-series Adapter Header J7 with jumper installed (Secure To disable Secure Firmware enabled) Firmware, remove... -
Page 20: Installing The Adapter
2. Installation Installing the Adapter Header J24 with jumper installed (Secure To disable Secure Firmware enabled) Firmware, remove the jumper from J24 Figure 2-7 Secure Jumper Location J24 on OCe14102B-NT and -UT-series Adapters Installing the Adapter To install the adapter in the computer, perform the following steps: 1. -
Page 21: Attaching Devices To The Adapter
3. Attaching Devices to the Adapter Connecting Devices to Adapters Using a DAC or AOC Cable 3. Attaching Devices to the Adapter The following sections describe how to connect devices to the adapter using different cable types. Connecting Devices to Adapters Using a DAC or AOC Cable The following adapters can be connected to a DAC or AOC cable: OCe14101B-NX... -
Page 22: Figure 3-1 Connecting A Dac Cable To The Oce14100B-Series -Nx/-Ux
3. Attaching Devices to the Adapter Connecting Devices to Adapters Using a DAC or AOC Cable 2. After confirming that there are no optical transceivers installed, insert the DAC or AOC transceiver into the SFP+ cage on the OCe14100B-series adapter as shown in Figure 3-1 or the OCe14400B-series adapter as shown in Figure 3-2. -
Page 23: Emulex Oneconnect Accessories
3. Attaching Devices to the Adapter Connecting Devices to Adapters Using a DAC or AOC Cable Emulex OneConnect Accessories Table 3-3 and Table 3-4 provide model number, name, interface, and required quantities, for ordering additional or replacement transceivers or cables. Table 3-3 OCe14101B-NX, OCe14102B-NX, and OCe14104B-NX/-UX Adapter Emulex OneConnect Accessories Model Number... -
Page 24: Connecting Devices To Adapters Using An Optical Cable With Lc Connectors
3. Attaching Devices to the Adapter Connecting Devices to Adapters Using an Optical Cable with LC Connectors Connecting Devices to Adapters Using an Optical Cable with LC Connectors The following adapters can be connected to a fiber optic cable with an embedded optical transceiver: OCe14101B-NM ... -
Page 25: Figure 3-3 Installing An Optical Transceiver For The Oce14000B-Series
3. Attaching Devices to the Adapter Connecting Devices to Adapters Using an Optical Cable with LC Connectors To attach devices to the adapter: 1. Connect the optical cable to the adapter. When connecting an optical cable, ensure that the cages have optical transceivers installed in them (Figure 3-3 on page 25). Figure 3-3 Installing an Optical Transceiver for the OCe14000B-series -NM/-UM Adapters 2. -
Page 26: Connecting Devices To Adapters Using A Utp Or Cat Cable
3. Attaching Devices to the Adapter Connecting Devices to Adapters Using a UTP or CAT Cable Connecting Devices to Adapters Using a UTP or CAT Cable The OCe14102B-NT and OCe14102B-UT adapters can be connected with an unshielded twisted pair (UTP) or shielded twisted pair (STP) copper cable (commonly referred to as a Category or 'CAT' cable). -
Page 27: Applying Power And Viewing The Leds
4. Applying Power and Viewing the LEDS Applying Power 4. Applying Power and Viewing the LEDS This section provides instructions on how to apply power and how to interpret the LEDs for various adapter models. Applying Power To apply power: 1. -
Page 28: Viewing The Leds
4. Applying Power and Viewing the LEDS Viewing the LEDs Viewing the LEDs The LED indicators in Figure 4-1 pertain to the following adapter models: OCe14101B-NM/-NX OCe14102B-NM/-NX OCe14102B-UX/-UM Each port connector has one amber and one green LED. Figure 4-1 OCe14101B-NM/-NX, OCe14102B-NM/-NX, and OCe14102B-UX/-UM Adapter LED Indicators The LED indicators as shown in Figure 4-2 pertain to the single port OCe14401B-NX/-UX adapter models. -
Page 29: Figure 4-3 Oce14102B-Nt And Oce14102B-Ut Led Indicators
4. Applying Power and Viewing the LEDS Viewing the LEDs The LED indicators as shown in Figure 4-3 pertain to the dual port OCe14102B-NT/-UT adapter models. Each port connector has one green and one amber LED. Figure 4-3 OCe14102B-NT and OCe14102B-UT LED Indicators The LED indicators in Figure 4-4 pertain to the OCe14104B-NM and OCe14104B-UM adapter models. -
Page 30: References
5. References Specifications 5. References Specifications Table 5-1 provides information for OCe14101B, OCe14102B, OCe14104B, and OCe14401B adapters. Table 5-1 Adapter Specifications Parameter Range Physical Dimensions OCe14104B-NX, OCe14104B-UX, OCe14104B-NM, and OCE14104B-UM four-port SFP+ adapters are available in the standard, full-height form factor only. Standard, full-height form factor, 6.600 inches by 4.3760 inches (167.64 ... -
Page 31: Fcc And Regulatory Notices
5. References FCC and Regulatory Notices Table 5-1 Adapter Specifications (Continued) Parameter Range Agency Approvals • Class 1 Laser Product per DHHS 21CFR (J) & EN60825-1 when equipped with approved optical devices • UL recognized to UL60950-1 2nd Edition • cUR recognized to CSA 22.2, No. 60950-1-07 •... - Page 32 5. References FCC and Regulatory Notices expressly approved by Emulex could void the user's authority to operate this equipment. The above statement applies to products marketed in the USA. This class A digital apparatus meets all requirements of the Industry Canada (IC) Interference - Causing Equipment Standard (ICES-003).
-
Page 33: Declaration Of Conformity
5. References Declaration of Conformity Declaration of Conformity OCe14000B-series Adapters This equipment complies with CISPR22/EN55022 Class A. WARNING: This is a class A product. In a domestic environment, this product may cause radio interference requiring the user to take adequate measures. OneConnect OCe14000B-series Adapters Installation Manual pub-005129 Rev. - Page 34 5. References Laser Safety Notice Note: Changes or modifications not expressly approved by Emulex Corporation, including the use of non-Emulex approved optical transceivers, could void the user's authority to operate this equipment. DECLARATION OF CONFORMITY Manufacturer: Emulex Corporation 3333 Susan Street Costa Mesa, CA.
- Page 35 5. References Laser Safety Notice The use of non-Emulex approved optical transceivers, or transceivers which do not comply with the Class 1 radiation performance requirements defined in DHHS/CDRH 21CFR Sub-chapter J and IEC 60825-1, may expose the user to hazardous laser radiation, and such devices should not be used with Emulex products.
Need help?
Do you have a question about the Emulex OCe14000B Series and is the answer not in the manual?
Questions and answers