Subscribe to Our Youtube Channel
Summary of Contents for CUE rfCUE 99
- Page 1 User Manual rfCUE 99 Version 03 CUE spol. s r.o., Na Dolinách 6, 147 00 Praha 4, Czech Republic phone: +420 241 433 555 fax: +420 241 432 446 www.cuesystem.com e-mail: info@cue.cz...
- Page 2 User Manual rfCUE 99 UM010_03, Version 03, 01.04.2003 Copyright © CUE, spol. s r.o. Praha, Czech Republic 1990 - 2003. All rights reserved. Specifications are subject to change without prior notice.
-
Page 3: Table Of Contents
Table of Contents Introduction ............................ 4 1.1. Overview ..................................4 1.2. Models...................................4 1.3. Features ..................................4 1.4. Programming.................................4 Using ............................... 5 Operational Description ........................ 6 3.1. Backlight in Active and Sleeping Mode .........................6 3.2. Transmit / Receive Indication ............................6 3.3. Operation of the Feedback Indication ...........................6 Charging ............................ -
Page 4: Introduction
Designed to fit perfectly in your hand, the rfCUE 99 is constructed of solid wood with stainless steel trim and is available in mahogany, birch, white birch and oak finishes to blend with the most critical environments. -
Page 5: Using
2. Using The rfCUE 99 is connected to the rest of control system via RF communication with the unit rfbaseCUE. The unit rfbaseCUE then provides a connection via RS-485 bus to the control units Assistant or Assistant-S. For further information see User Manual rfbaseCUE. -
Page 6: Operational Description
The sleeping mode is terminated after pressing the back-light button or any other button on the rfCUE, the backlight LED will light on for the time of about 6 - 8 seconds the rfCUE 99 remains active. Then the rfCUE 99 goes to sleeping mode to reduce power consumption. In sleeping mode the rfCUE 99 does not transmit or receive any RF signals. -
Page 7: Charging
99 to the charger at the end of every working day. Connect the charger to the rfCUE 99 also in case you find the lower range of the transmission or when the back-light brightness is reduced. -
Page 8: Button Labels
5. Button Labels The labeling is provided by a plastic foil inserted under the buttons. Foil preparation steps 1. Use AutoCAD file named CS0170.0007.1-Foil.dwg for preparation of a layout. This file is available on www.cuesystem.com. The foil shape is described on the picture below. 2. -
Page 9: Addressing
The address of the rfCUE 99 can be in set in the range 0 to 9 and can be changed in the rfCUE 99 modify mode - see chapter Modify Mode. When the address is set to 1 the button codes are in range 33 to 64, for address 2 the button codes are in range 65 to 96 and so on. -
Page 10: Modify Mode
6. On the LEDs under the first 8 buttons there will be a binary value of current address of the rfCUE 99 displayed. The leftmost upper LED means LSB bit. Red color means log. 1. When current address is 0 then the first 8 LEDs remain green, when current address is 1 then the leftmost upper LED goes red and the rest remain green, …... -
Page 11: How To Modify The Address
6. The LED under the back-light button starts to blink several times. 7. On the LEDs under first 8 buttons there will be the binary value of new address of rfCUE 99 displayed. The same value is displayed on LEDs in 3rd and 4th row and in complement on 5th and 6th row as well as on 7th and 8th row. -
Page 12: Troubleshooting
Charge the accumulator immediately. 3. The RF operating range is short. • Check the accumulators in the rfCUE 99 and recharge them. • Check the presence of disturbing RF signals (frequencies of other RF operating equipment in the installation). -
Page 13: Specifications And Mechanical Drawings
9. Specifications and Mechanical Drawings Buttons layout........(32) buttons Buttons back-light ........Two-color, red or green programmable Communication........Two-way, radio frequency 433 / 869 / 914 MHz Power supply ........NiMH rechargeable battery pack Enclosure..........Wood - stainless steel panel Dimensions (WxHxD) ......217 mm (8.5”) x 70 mm (2.8”) x 32 mm (1.3”) Weight..........0.6 kg / 1.6 lb Supplied accessories......Charger, 110 - 230 VAC, 50 / 60 Hz All dimensions are in mm. -
Page 14: Software And Firmware License
License Grant CUE grants to You, as an individual, a license to install and use one (1) copy of the Software on a single computer at a time; provided, however, that You may make copies of the Software solely for Your development of applications for CUE hardware and demonstration versions of such applications. -
Page 15: Warranty Conditions
CUE provides warranty for all CUE products for a period of 3 years from the day of purchase. The provided warranty for touch screens is 2 years from the day of purchase. CUE accepts reclamation of 5 not properly working dots and more (2 dots join – 1 counts). -
Page 16: Ce Declaration Of Conformity
ST0007 Guide, CS0188 touchCUE-SRF, CS0171 rfbaseCUE, ST0013 monitorCUE-V, CS0203 monitorCUE, CS0190 touchCUE-V /i, CS0151 PC Interface 485 CS0170 rfCUE 99, CS0170 rfCUE 99, CS0149 irCUE 99, CS0133 irCUE, CS0080 irCUE Receiver, CS0169 irCUE Receiver 485, CS0221 keypadCUE-1G, CS0222 keypadCUE-2G, CS0223 keypadCUE-3G,... -
Page 17: Fcc
13. FCC Caution Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. - Page 18 Notes User Manual rfCUE www.cuesystem.com Page 18 of 18...
Need help?
Do you have a question about the rfCUE 99 and is the answer not in the manual?
Questions and answers