Advertisement
Quick Links
Advertisement
Summary of Contents for Ryonet Sgreen Washout booth
- Page 1 Assembly Instructions...
-
Page 3: Tools Required
MFPB-SGWASHLEG MFSA-SGWASHDW Sgreen washout hardware kit MFCO-EDGETRIM Black sheet metal edge trim MFPB-SGWASHSID Sgreen washout booth side panel (RH shown) MFLS-SGWASHGST Sgreen washout booth rear gussets MFPB-SGWASHBKT2 Sgreen washout booth side rear panel brackets MFPB-SGWASHBKT1 Sgreen washout booth lower rear panel brackets... -
Page 4: Parts Required
Parts Required: What’ s in the box... - Page 5 Name/ID Description Qty. MFPB-SGWASHSTOFF Sgreen Washout booth Screen holding stand-off MFCO-SGWASHCAULK Clear Caulk, Acrylic, 5.5 oz. Tube PRHD-BTN1/4NC1/2SS 1/4-20 x 1/2 Button Head Allen Bolt Stainless steel PRHD-WA1/4NEOBONDSS 1/4” Neobond Stainless steel conical washer PRHD-ACN1/4NCGR5ZC 1/4-20 Acorn Nut Nickel PRHD-WA1/4USSGR5ZC...
- Page 6 Step 1 Install the legs (1) to the main sink pan (2). Make sure the Neobond washers are on the inside of the sink and the standard flat washers are outside of the sink. Note: Refer to page 2 for hardware detail.
- Page 7 Step 2 Install the 27-7/8” lower rear panel bracket (1) to the main sink body (2). Only attach the center 2 holes at this time. Do NOT fully tighten at this step. Neobond washers are inside of the sink and standard washers outside of the sink.
- Page 8 Step 3 Install the side panels (1) to the main sink body (2). Fully tighten the hardware. Neobond washers are inside of the sink and standard flat washers are outside of the sink. Note: Refer to Page 2 for hardware detail.
- Page 9 Step 4 Partially attach the rear gussets (1) to the main sink body and side panels (2). NOTE: Only attach the two places shown in the drawing below. Note: Refer to Page 2 for hardware detail.
- Page 10 Step 5 Attach the trim seal to the side panels of the washout sink. Some trimming may be required at this step. Note: Refer to Page 2 for hardware detail.
- Page 11 Step 6 Install the 30-3/8” side rear panel brackets (1) to the side panels of the washout sink (2). DO NOT fully tighten hardware at this time. Omit the upper and lower hardware at this step. Neobond washers on the inside of the sink and the standard flat washers are on the outside.
- Page 12 Step 7 Install the lower rear corner hardware to the back panel holding brackets. DO NOT fully tighten the hardware at this time. No flat washers in this step. Note: Refer to Page 2 for hardware detail.
- Page 13 Step 8 Attach the upper cross bar (1) to side panel (2) with the suppled hardware. DO NOT full tighten the hardware at this time. No flat washers are in lower hole. Note: Refer to Page 2 for hardware detail.
- Page 14 Step 9 Slide the rear panel of the washout booth into the channels between the brackets and the side panels. Push down into the lower bracket. Align the top of back panel with the top edge of the side holding brackets.
- Page 15 Step 10 Attach the 26-3/8” upper back panel bracket (1) & upper spacer (2) to the top cross bar (3). Fully tighten the hardware at this step. Spacer is between the back acrylic panel and the top cross bar. No flat washers this step.
- Page 16 Step 11 Install the final hardware in the upper corner of the side panels. Fully tighten the hardware at this time. After all hardware is tight, use supplied caulk to seal up all seams where water could leak. Allow to dry per caulking instructions.
- Page 17 NOTES: NOTE: Logos, graphic elements and or photo images contained in this document may not be reproduced without the written consent of Ryonet...
Need help?
Do you have a question about the Sgreen Washout booth and is the answer not in the manual?
Questions and answers