Related Manuals for Fomei Digitalis Pro TX 400TTL
Summary of Contents for Fomei Digitalis Pro TX 400TTL
- Page 1 Battery flash FY3051 FY3057 Digitalis Pro TX 400/600 TTL FY3004 Flash trigger TX FY3005 TS-5 Canon/Nikon/Fuji/Sony FY3058 FY3059 USER GUIDE...
- Page 2 Safety warning: 1. Keep this product out of reach the rain or humidity to avoid damage or injury. 2. Do not disassemble the product. In case of damage contact a service FOMEI or contractual service with trained professionals. 3. If the product is disassembled, you will not be covered under warranty.
-
Page 3: Table Of Contents
TABLE OF CONTENT A. ABOUT PRODUCT B. PRODUCT OVERVIEW C. PRODUCT USAGE D. TECHNICAL INFORMATIONS E. RECOMMENDED ACCESSORIES WWW.FOMEI.COM... -
Page 4: About Product
TTL performance. TTL and HSS mode should only be used with TS-5 wireless con- troller and trigger. Package contains: • Flash • Battery • Charger • Comfortable strap 1. Flash tube 2. Bracket 3. Sync sensor 4. Shoulder strap mount 5. Battery release button 6. Battery/AC adaptor (does not included) WWW.FOMEI.COM... -
Page 5: Product Overview
B. PRODUCT OVERVIEW 7. LCD display 8. Flash status indicator 9. Control buttons 10. Power on/power off button 11. Control buttons 12. Battery status button 13. Battery status display WWW.FOMEI.COM... -
Page 6: Product Usage
Designate up to 4 groups and these groups can be controled at the same time. • TS-5 wireless trigger group should be set to the same designated group in TX TTL flash in order to operate the flash. • Press the A, B, C and D buttons on wireless trigger for settings. WWW.FOMEI.COM... - Page 7 When shooting under <TTL> auto flash mode under various environments, it may demand a minor adjusting exposure value. After checking your photograph for under and overexposure, press the + - buttons on the TS-5 to adjust exposure compensati- on with an increment of 0.1 F-Stops. WWW.FOMEI.COM...
- Page 8 • After setting up the M mode on TS-5, manipulate „+/-“ buttons to adjust flash output from 1/1 full power to the lowest output of 1/256 with an increment of 0.1 F-Stops. WWW.FOMEI.COM...
- Page 9 S1- When a regular flash fires, slaves detect flash and firessimultaneously. • S2- When a TTL flash fires, slaves detect flash and fires simultaneously • Applicable only in M mode. Sound settings • Press SOUND button to turn the sound ON/OFF WWW.FOMEI.COM...
- Page 10 To set the number of flashes, press „T“ on the TS-5 transmitter until the display starts blinking. • Next, set your preferred number of flashes using „+/-“ buttons. • To set the flash frequency, press „Hz“ until the display starts blinking. • Next, set your preferred frequency using the navigational „+/-“ buttons. WWW.FOMEI.COM...
- Page 11 Please refer to the table below to calculate shutter speed • In order to prevent flash from overheating and malfunctioning, refrain from firing flash no more than 10 times in multi-flash mode. • After firing in succession, flash should be left unused for at least 5 minutes. WWW.FOMEI.COM...
- Page 12 Settings reset • To reset TX TTL, press „MODE“ button for 2 seconds or longer. All settings for group, channel, exposure compensation, sync and flash output are reset. WWW.FOMEI.COM...
-
Page 13: Technical Informations
Pilot light 20W LED RF receiver Built-in (works only with TS-5) Dimensions without battery 125x125x265mm Weight without battery 1,9 / 2,0 kg E. RECOMMENDED ACCESSORIES Trigger TS-5 AC adaptor Spare battery FY3004 / FY3005 FY3047 FY3046 FY3058 / FY3059 WWW.FOMEI.COM... - Page 14 Photo: Dan Vojtěch WWW.FOMEI.COM...
- Page 15 Photo: Dan Vojtěch WWW.FOMEI.COM...
- Page 16 FOMEI s.r.o. Machkova 587 500 11 Hradec Králové sls@fomei.com www.fomei.com FOMEI Slovakia s.r.o Za Kasárňou 1 831 03 Bratislava info@fomei.sk www.fomei.sk FOMEI Servis Tel.: +420 495 056 505 E-mail: servis@fomei.com...
Need help?
Do you have a question about the Digitalis Pro TX 400TTL and is the answer not in the manual?
Questions and answers