Table of Contents
Advertisement
Quick Links
KBM
-28U
®
INVERTED PORTABLE PLATE
EDGE BEVELLING MACHINE
Adjustable bevel head produces bevel
angles from 22.5º through 55º
Supplied with angle bevel pin for 30º
Other bevel angle pins are available
upon request.
NOTE: Machine shipped with the 30º
bevel pin in place.
PARTS LIST
&
OPERATING INSTRUCTIONS
Website: www.gullco.com
Distributed by:
Revised: May 14, 2018
GD-055
Advertisement
Table of Contents
Summary of Contents for GULLCO KBM-28U
- Page 1 22.5º through 55º Supplied with angle bevel pin for 30º Other bevel angle pins are available upon request. NOTE: Machine shipped with the 30º bevel pin in place. PARTS LIST & OPERATING INSTRUCTIONS Website: www.gullco.com Distributed by: Revised: May 14, 2018 GD-055...
-
Page 3: Machine Specifications
® This manual (in combination with the KBM -28 manual, GD-047) covers the operation instructions, ® maintenance requirements and provides parts lists for the Gullco Inverted Plate Edge Bevelling Machine, part number: KBM -28U. ® DECLARATION OF CONFORMITY - CE - designed and manufactured in compliance with 2006/42/EC provisions and further amendments. - Page 4 LIFTING (HOISTING) The recommended method of lifting (hoisting) the Gullco KBM -28U Inverted Portable Plate Edge ® Bevelling machine is to use two (2) equal length slings of sufficient capacity (924 lbs [420 Kg] minimum), fed through the machine as shown below. All lifting (hoisting) equipment must be suitably rated and clearly identified to be of adequate capacity.
-
Page 5: Installation
INSTALLATION ELECTRICAL CONNECTION WARNING! As shown in the accompanying drawing, the cutter rotation MUST be clockwise (as viewed from the front). IT IS IMPORTANT THAT THIS ROTATION DIRECTION BE CORRECT OTHERWISE DAMAGE TO THE MACHINE MAY OCCUR AND WARRANTY WILL BE VOID. Be certain to check the cutter rotation before operating the machine. -
Page 6: Frequent Inspections
INSPECTION & MAINTENANCE FREQUENT INSPECTIONS IMPORTANT: Due to the inverted operating position of the KBM bevelling machine, contamination from the bevelled plate tends to build-up around the back of the cutter and may eventually work its way into the gearbox bearing causing machine damage, if not regularly cleaned and inspected. - Page 7 LIFTING JACK ASSEMBLY BREAKDOWN Drawing Number: KBM-18U-004 ITEM PART NUMBER DESCRIPTION KBM-18U-004-1 JACK HANDLE GK-108-052 1/4-20UNC x 1 HEX BOLT GK-109-050 1/4-20UNC HEX NUT GK-117-033 3/16 x 3/4 SPRING PIN...
- Page 8 -28U GENERAL ASSEMBLY BREAKDOWN ® Drawing Number: KBM-28U-100...
- Page 9 -28U GENERAL ASSEMBLY BREAKDOWN ® Drawing Number: KBM-28U-100...
- Page 10 PIVOT ARM ASSEMBLY BREAKDOWN Part Number: KBM-28U-044...
- Page 11 SLIDE BASE ASSEMBLY BREAKDOWN Part Number: KBM-28U-043...
- Page 12 STARTER ASSEMBLY BREAKDOWN Drawing Number: KBM-28U-056...
- Page 13 MANUAL STARTER ASSEMBLY BREAKDOWN Drawing Number: KBM-28-225-1/2/3...
-
Page 14: Wiring Schematic
-28 WIRING SCHEMATIC ® Drawing Number: KBM-28-225-SCH... - Page 15 OPTIONAL AIR JET ASSEMBLY BREAKDOWN Drawing Number: KBM-28U-018 ITEM PART NO. DESCRIPTION QTY. GF-168-010 QUICK CONNECT COUPLER GBM-25-018 QUICK CONNECT PLUG GBM-25-017 FLOW VALVE KBM-28U-019 FORMED AIR PIPE KBM-28U-016 AIR BLOWER MOUNTING CLAMP KBM-28U-017 MOUNT PLATE GK-107-127 M5-0.8 x 25mm SHCS GK-107-131 M5-0.8 x 12mm SHCS...
-
Page 16: Additional Notes
Pgs. 10, 11 & 12 Updated starter details and part numbers. ADDITIONAL NOTES Specifications and products are subject to change without notice. KAT, Moggy, Sam, KATBAK & KBM are registered trademarks of Gullco International Enterprises Ltd. Only use genuine/authorized replacement parts. - Page 18 www.GULLCO.com...
Need help?
Do you have a question about the KBM-28U and is the answer not in the manual?
Questions and answers