Advertisement
Quick Links
Camera and Electronic Products for Integrators
I
N
-
W
™
R
I
N
-
W
™
R
A
L
L
A
L
L
Recessed Camera Mounting Systems for Sony®, Polycom®
EagleEye®, LifeSize®, TANDBERG® PrecisionHD® PTZ Cameras and
Vaddio™ EZ Camera™ Interface Module Cable System Packages
Figure 1: IN-Wall Systems (clockwise, left to right), Sony BRC-H700, EVI-D70, TANDBERG Precision HD, LifeSize, Sony
BRC-Z700, Polycom EagleEye, Sony EVI-HD1 and Sony BRC-300
OVERVIEW:
The Vaddio IN-Wall camera mounting systems are an attractive way to mount PTZ cameras on a wall
where room aesthetics are critical. These mounting systems use the depth of the wall cavity to recess the
camera into the wall, minimizing the camera's extension into the room and providing a more finished look
to the installation.
Cameras from Sony (BRC-H700, BRC-Z700, BRC-300, EVI-D70 and EVI-HD1),
TANDBERG (Precision HD), Polycom (EagleEye and EagleEye 1080 HD) and LifeSize were selected
and the camera enclosures were carefully designed and sized to fit the Vaddio EZCamera Interface
Module (EZIM) in the back of the box to enable use of the Vaddio Quick-Connect CCU and PRO CAT-5
cabling systems for applicable cameras (see below). For the EVI-D70, the Vaddio EZ Camera Shoe can
be attached to the back of the camera. Each system consists of an in-wall mounting box and face frame
which are both powder coated white, but can be painted to match any décor.
IN-Wall Enclosure Supported Cameras and Part Numbers
Part Number
Compatible Camera Systems
999-2225-012
Sony EVI-D70 , Vaddio WallVIEW 70 System
999-2225-013
Sony BRC-300, Vaddio WallVIEW CCU or PRO 300 PTZ System
Sony EVI-HD1, Vaddio WallVIEW CCU or PRO HD1 PTZ System,
999-2225-014
WallVIEW EagleEye 1080 HD and Polycom EagleEye 1080 HD
Vaddio WallVIEW PRO EagleEye, Polycom EagleEye,
999-2225-015
TANDBERG Precision HD and LifeSize
999-2225-016
Sony BRC-H700, Vaddio WallVIEW CCU or PRO H700 PTZ System
999-2225-017
Sony BRC-Z700, Vaddio WallVIEW CCU or PRO Z700 PTZ System
UNPACKING:
Carefully remove the product and all of the parts from the packaging and identify the following parts:
•
Back Box Enclosure
•
Camera Platform
•
Face Frame
•
Mounting Hardware
•
Documentation
(Camera Not Included)
©2008 Vaddio - All Rights Reserved. IN-Wall Enclosures - Document Number 341-744 Rev C
C
C
E
C
E
S
S
E
D
A
E
C
E
S
S
E
D
A
Installation and User Guide
M
M
M
E
R
A
O
U
N
M
E
R
A
O
U
N
S
S
T
I
N
G
Y
S
T
E
M
T
I
N
G
Y
S
T
E
M
S
S
Advertisement
Related Manuals for VADDIO IN-Wall 999-2225-012
Summary of Contents for VADDIO IN-Wall 999-2225-012
- Page 1 Vaddio EZCamera Interface Module (EZIM) in the back of the box to enable use of the Vaddio Quick-Connect CCU and PRO CAT-5 cabling systems for applicable cameras (see below). For the EVI-D70, the Vaddio EZ Camera Shoe can be attached to the back of the camera.
- Page 2 ½” drywall covering the wall and minimizes the camera’s protrusion into the room. The extra depth accommodates the Vaddio EZIM for use with Cat. 5 cabling, or the EZ Camera Shoe for the EVI-D70. Each Enclosure is outfitted with three (3) conduit knockouts (2-sides, 1-top) for flexibility, along with a cable pass-through in the base of the platform for standard camera cabling.
- Page 3 IN-Wall Enclosures INSTALLATION (continued): 5) Remove the box from the wall and install the wall anchors. 6) Pull the cabling through the conduit knock-out and push the back box back into the opening. Be sure to leave enough slack in the cable to enable termination and the freedom to push the cable back into the wall cavity when the camera is attached to the platform.
- Page 4 Vaddio Customer service – Vaddio will test, repair, or replace the product or products without charge if the unit is under warranty and is found to be defective. If the product is out of warranty, Vaddio will test then repair the product or products.