Browning Torq/Gard Installation, Operation And Maintenance Instructions

Clutch

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

Torq/Gard

Clutch Installation,

Operation and Maintenance Instructions

• Read and follow all instructions carefully.

• Disconnect and lock out power before installation and

maintenance. Working on or near energized equipment can

result in severe injury or death.

• Do not operate equipment without guards in place. Exposed

equipment can result in severe injury or death.

Regal Beloit America, Inc.

7120 New Buffington Road

Florence, KY 41042

Application Engineering: 800 626 2093

www.regalbeloit.com

• Periodic inspections should be performed. Failure to perform

proper maintenance can result in premature product failure and

personal injury.

F O R M

8322E

Revised

January 2019

Table of Contents

Need help?

Do you have a question about the Torq/Gard and is the answer not in the manual?

Questions and answers

Summary of Contents for Browning Torq/Gard

Page 1 F O R M Regal Beloit America, Inc. 7120 New Buffington Road 8322E Florence, KY 41042 Revised Application Engineering: 800 626 2093 Torq/Gard Clutch Installation, ® January 2019 www.regalbeloit.com Operation and Maintenance Instructions • Periodic inspections should be performed. Failure to perform •...
Page 2 Torq/Gard chain drives can be used as the driving or driven member. See page 8 for sprocket availability. Keep all objects such as hands, clothing, tools, etc. away from rotating or moving parts.
Page 3 Table D–TGC400 and TGC800 Clutch The Torq/Gard clutch can be shaft mounted from the adapter or Detector End detector end of the hub. The required shaft set screw lengths vary Set Scr.
Page 4 The shaft length must be at least equal to the bushing length Refer to the Torq/Gard clutch dimension prints on page 8 for to insure engagement of the Torq/Gard clutch bearings. the detector plate “travel” . ® Limited shaft lengths or high overhung load applications When mounting the limit/prox.
Page 5 Do greater misalignment capabilities are not exceed the maximum RPM shown in The Torq/Gard clutch is delivered with the torque set at the low required. Either side of the Torq/Gard the Torq/Gard clutch selection table.
Page 6 Single Position The Torq/Gard clutch always resets in the same position when tripped. All Torq/Gard clutches are fully reversible. ® Lubrication The Torq/Gard clutch is factory lubricated with Mobilith AW2 and does not require additional lubrication for ® years, under normal operating conditions. Clutches used in extreme operating applications may be opened for regreasing.
Page 7 Parts List (Models TG & TGC) Part Numbers Item Qty Description Adjusting Nut A-58211 A-58211 A-58238 A-16512 A-16346 B-16680 B-16680 Spring A-58255-1 A-58255-2 A-58255-3 A-15731 A-13732 A-16682-1 A-17538-1 Spring A-16682-2 A-17538-2 Button A-58168 A-58168 A-58171 A-15727 A-13407 A-16685 A-16685 Body D-58675 D-58675 C-58695...
Page 8 C18640 TGC400 CHCFR9Q C18641 TGC800 CHCFR10Q C18642 Regal, Browning, Browning Split Taper, Ever-flex, Gearbelt and Torq/Gard are trademarks of Regal Beloit Corporation or one of its affiliated companies. ©2015, 2019 Regal Beloit Corporation, All Rights Reserved. MCIM18028E • Form# 8322E...