Advertisement
WARNING: Use a welding head shield to protect your eyes and avoid exposing skin to the ultraviolet rays given off by the electric
‰
arc. Always wear protective clothing, insulating gloves and shoes. Keep all protective items clean and undamaged.
Remove ill fitting clothing before wearing protective clothing. Also remove watches, rings and other loose jewellery and contain long
9
hair.
Stand correctly, keeping a good footing and balance and ensure that the floor is not slippery. Wear non-slip shoes.
9
ensure that the workpiece is correctly secured before cutting.
9
Avoid unintentional contact with the workpiece. Accidental or uncontrolled switching on of the torch may be dangerous and will wear
9
the nozzle.
Keep unauthorised persons away from the work area. Any persons working within the area must wear the same protective items as
9
the operator.
Do not use cables and torch if the insulation is worn or connections are loose.
8
Do not attempt to fit any unauthorised torch or other component to the plasma cutting unit.
8
Do not cut surfaces that are painted, galvanic coated, oily or greasy. These surfaces must be cleaned first. Wear a respirator suitable
8
for protection against toxic fumes, smoke and gases.
Do not use cables over 10m in length.
8
Do not connect the return cable to any structure which is not part of the workpiece (other than a metal work bench supporting the
8
workpiece).
▲
DanGer! Do not cut near flammable materials - solids, liquids, or gases. Remove all flammable materials such as waste rags etc.
Do not cut containers or pipes which have held flammable materials - gases, liquids or solids. Do not cut materials that have
8
been cleaned with chlorinated solvents (or near such solvents) as vapours from the arc action may produce toxic gases.
Do not operate the inverter while under the influence of drugs, alcohol or intoxicating medication, or if tired.
8
Do not use the plasma inverter for a task it is not designed to perform.
8
Do not operate the plasma inverter if any parts are damaged or missing as this may cause failure and/or personal injury.
8
Do not carry, or pull, the inverter by the leads or cables. Do not strain or bend the cables, protect them from sharp or abrasive
8
items and Do not stand on them.
Protect cables from heat. long lengths of slack must be gathered and neatly coiled. Do not place cables where they will endanger
9
others.
Do not hold unsecured workpiece in your hand.
8
Do not get the plasma inverter wet or use in damp or wet locations or areas where there is condensation.
8
Do not touch the workpiece close to the cut as it will be very hot. Allow to cool. The cut edge of the workpiece will also be very
8
sharp.
Do not touch the torch immediately after use. Allow the torch to cool.
8
When not in use store the unit in a safe, dry, childproof area.
9
2. introDUction
Features an integral compressor yet weighs only 17kg. Inverter power supply fitted with plasma cutter control circuitry. With built in 4mtr plasma
torch, earth cable and 4mtr gas hose. Features LED display to show the current output and dial adjustment from 15-40Amp. Three indication
lights show voltage input, amps output and thermal overload. Uses air to strike arc making it suitable for use near electrical equipment. Ideal for
cutting steel, stainless, galvanised steel, aluminium, copper and brass. IP21S rated. 230V supply.
3. speciFication
model no: ............................................................. PP40PlUS
Power output: .............................................................15-40A
duty Cycle: ...................... 20%@40A, 30%@35A, 60%@25A
maximum Cutting Thickness: ....................................... 10mm
Absorbed power: .......................................................... 6.9kW
Supply: ...........................................................................230V
Insulation:.............................................................................F
Protection: .................................................................... IP21S
Weight: ........................................................................ 18.5kg
Replacement Consumables:
electrode Short (pack Qty.): ....................... PP40PlUS.e (5)
nozzle, Short (pack Qty.): ........................... PP40PlUS.n (5)
diffuser (pack Qty.): .................................... PP40PlUS.d (5)
Safety cap (pack Qty.): .............................PP40PlUS.SC (2)
4. contents
4.1.
Remove contents from carton and check against contents list below.
item
Plasma cutter
Grounding cable
Cutting torch
electrode
Tip
Instruction manual
© Jack Sealey limited
qty.
1
1
1
3
3
1
Original Language Version
PP40PlUS | Issue:1 29/08/18
Advertisement
