Sealey Power Tools SA623.V2 Instructions

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLease reaD tHese instructions carefuLLy. note tHe safe oPerationaL reQuireMents, WarninGs anD cautions.
use tHis ProDuct correctLy anD WitH care for tHe PurPose for WHicH it is intenDeD. faiLure to Do so May cause
DaMaGe or PersonaL inJury anD WiLL inVaLiDate tHe Warranty. PLease KeeP instructions safe for future use.
1. safety instructions
3 Follow all workshop health & safety rules, regulations, and conditions when using screwdriver.
p WarninG! Disconnect from air supply before changing accessories or servicing.
3 Maintain screwdriver in good condition and replace any damaged or worn parts. Use
genuine parts only. Non-authorised parts may be dangerous and will invalidate the warranty.
p WarninG! Check correct air pressure is maintained and not exceeded. We recommended
90psi.
3 Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each
use and ensure that all connections are secure.
3 Wear approved safety eye and ear protection.
3 Keep screwdriver bits clean and in good condition for best and safest performance.
3 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3 Secure non stable work piece with a clamp, vice or other adequate holding device.
3 Ensure the screwdriver bit is secure in the chuck.
3 Avoid unintentional starting.
3 Keep children and unauthorised persons away from the working area.
7 Do not get the
7 Do not hold the workpiece by hand. Use clamps or a vice to secure the workpiece.
7 Do not use the screwdriver for a task it is not designed to perform.
p WarninG! Do not use screwdriver if damaged or faulty. Contact your local service agent.
7 Do not use screwdriver unless you have been instructed in its use by a qualified person.
7 Do not drop, throw or abuse the screwdriver.
7 Do not carry the screwdriver by the air hose, or yank the hose from the air supply.
7 Do not operate screwdriver if you are tired, under the influence of alcohol, drugs or
intoxicating medication.
7 Do not carry screwdriver with your hand on the power trigger in order to avoid unintentional
starting.
7 Do not direct air from the air hose at yourself or others.
3 When not in use disconnect from air supply and store in a safe, dry, childproof location.
2. introDuction & sPecifications
Compact design is ideal for accessing work
areas where space is limited. Composite
lightweight housing reduces effects of chill on
operator's hands. Fully reversible with thumb
control on side of motor housing. Air motor with
quality bearings for smooth and powerful
operation. Features 6mm quick-release chuck
for fast bit changes. Suitable for the professional
workshop.
screwdriver wet or use in damp or wet locations.
Chuck size . . . . . . . . . . . . . . .6mm Hex
Free speed . . . . . . . . . . . . . . 11000rpm
Torque range . . . . . . . . . . . . . . 175lb.in
Air consumption . . . . . . . . . . . . . . 3cfm
Operating pressure. . . . . . . . . . . . 90psi
Air inlet size . . . . . . . . . . . . . . 1/4" BSP
Weight . . . . . . . . . . . . . . . . . . . . . 0.7kg
Noise . . . . . . . . . . . . . . . . . . . . .92dB.A
Original Language Version
INSTRUCTIONS FOR:
air PistoL screWDriVer
PreMier
sa623.V2
MODEL No:
SA623.V2 Issue: 1 - 17/10/11