Page 2
1. Packaging content A. Video doorbell unit B. Mounting wrench C. Mounting bracket D. Hex screw E. Screw plugs F. Screws G. Extra doorbell 2. Parts & Buttons FRONT 1. Microphone 2. Night Sensor 3. Camera 4. PIR Motion Sensor 5.
Note: Reset & setup button: Press the reset button and hold for at least 5 seconds to add the device MOUNTING BRACKET A: Hole for screw B: Hole for cable C: Hole for fastener 3. Installation instructions NOTE: Before step 6, please read chapter 4, 5 and 6 to connect firstly to the wi-fi correct. 1.
Page 4
2. (optional) Insert an SD/TF card into the Micro SD cardslot. Note: Make sure the device is turned OFF when you insert an SD/TF card into the slot. SD/TF cards with capacity up to 64GB are supported. 3. Fix the mounting bracket to the desired place on the wall or door. Start by holding the bracket against the wall and mark with a pencil the place where to drill the holes.
Page 5
4. Connect the power wires, for AC/DC power, use the bottom 2 screws (as described on this scheme) DC: AC 8-16V or DC 9-24V with no specific + or - pin Optionally, if you have a smart lock; you can connect it here also: There are 2 kinds of electric door locks;...
Page 6
6. Use the mounting wrench and the 2 HEX screws to finish attaching the video doorbell onto the bracket. 4. Download the MrSafeBell app in the Apple app store or on Google play store. 5. Register the user account 1. Open the app and grant the app access to the app to record video, save pictures, record sound and the location.
Page 7
6. Setup the device Click on the “+” button to setup the device and then click “Setup Device” The setup wizard will now tell you to connect the power to the doorbell (as described in chapter 3); turn ON the doorbell and press “NEXT”, wait for the start up tone and the ‘calling button’to be visible and press “GOT IT”.
Page 8
Note: If you do NOT hear the Di-Di-Di-sound; press “NO” and execute the following step: Press the reset button (B) on the back of the doorbell for about 5 seconds until you hear a tone. The device will restart and after about 30 seconds you will hear the startup tone again and Di-Di-Di.
Page 9
Open the MrSafeBell app and click on the connected device. You can now give it a dedicated name (such as front door, back door, office,…). Please note that you are the first user to add the device, meaning that you are the administrator.
Page 10
7. Granting a family member access to the video doorbell You can have multiple members of your family connected to the doorbell. To connect someone, start by downloading the MrSafeBell app on the member’s smartphone. The new member has to register his user name, password and e-mail address. The administrator has to add this new user name, and then the new user can scan the QR code generated by the administrators app.
Page 12
1. Verpakkingsinhoud A. Video deurbel B. Montagesleutel C. Montagebeugel D. Hex schroef E. Pluggen F. Schroeven G. Extra deurbel 2. Onderdelen en toetsen VOOR 1. Microfoon 2. Nacht sensor 3. Camera 4. PIR bewegingssensor 5. LED indicator 6. Aanraaktoets 7. Luidspreker ACHTER A.
Opmerking: druk de reset- en insteltoets minstens 5 seconden in om het toestel toe te voegen MONTAGEBEUGEL A. Opening voor schroef B. Opening voor kabel C. Opening voor bevestiging 3. Montage Opmerking: gelieve hoofdstuk 4, 5 en 6 eerst te lezen (verbinding via wifi) alvorens aan stap 6 te beginnen 1.
Page 14
2. (optioneel)schuif een Micro SD/TF kaart in de micro SD kaart sleuf Opmerking: zorg dat het toestel UIT staat wanneer u een sd kaart inschuift. Sd kaarten tot 64GB worden ondersteund. 3. Bevestig de montagebeugel op de gewenste plaats op de muur of deur. Markeer eerst de gaten waar u de montagebeugel wenst te bevestigen en de gaten wenst te boren met een potlood.
Page 15
Mocht u een smart lock hebben, kan u deze hier ook verbinden: Er zijn twee types van elektrische deursloten: Normaal Open (NO) of Normaal Gesloten (NC). Als u echter uw type slot niet kent raden wij u aan de handleiding van uw slot te raadplegen maar in de meeste gevallen is dit Normaal Open (NO).
Page 16
6. Gebruik de montagesleutel en de 2 HEX schroeven om de video deurbel definitief te bevestigen op de beugel. 4. Download de MrSafeBell app via de Apple Store of Google Play 5. Registreer het Gebruikersaccount 1. Open de app en verleen deze toegang tot video opnames, bewaren van foto’s, geluidsopname en locatie.
Page 17
6. Toestel instellen Klik op de ‘+’ toets om het toestel in te stellen en klik dan op ‘Toestel Instellen’ De installatie Wizard zal u nu vragen de videodeurbel aan de stroom te verbinden (zoals beschreven in Hoofdstuk 3), zet de deurbel aan en druk op ‘VOLGENDE’, wacht tot de starttoon en de ‘oproeptoets’...
Page 18
U zal nu een ‘DI-DI-DI’ geluid horen. Druk ‘JA’ in de app. Opmerking: als u het ‘DI-DI-DI’ geluid niet hoort, druk op ‘NEE’ en voer de volgende stap uit; Druk gedurende vijf seconden op de reset toets (B) op de achterkant van de deurbel tot u een toon hoort.
Page 19
Druk op ‘START’ nadat de ‘oproeptoets’ zichtbaar is en echt DI-DI-DI geluid hoorbaar is. Ga naar de wifi instellingen van uw smartphone en selecteer het wifi netwerk “Bell-*****”. Het wachtwoord is bell@Door Klik op ‘OK’ en sluit af. Open de MrSafeBell app en klik op het verbonden toestel. U kan dit nu een persoonlijke naam geven (voordeur, achterdeur, kantoor, …)
Page 20
Gelieve er op te letten dat u de eerste gebruiker bent om het toestel toe te voegen, wat tevens betekent dat u de beheerder bent. Dit houdt in dat u gebruikers kan toevoegen én verwijderen. Klik op het instellings- en wifi-icoontje om het toestel met uw wifi te verbinden. Selecteer het wifi netwerk en geef het wachtwoord in om de video deurbel te verbinden aan uw eigen netwerk.
Page 21
8. De instellingen van uw verbonden deurbel veranderen Druk op het instellingsicoontje van uw verbonden deurbel om de volgende parameters te veranderen. Deurbel naam Systeem instellingen: hier kunt u de wachttijd van het gesprek dat dient aangenomen te worden wijzigen en kunt u de deurbel vanop afstand opnieuw opstarten Gebruikersbeheer: zie welke gezinsleden toegang hebben en/of videobeelden kunnen zien Bewegingsdetectie: zet de bewegingsmelder AAN of UIT en stel de gevoeligheid van de...
Need help?
Do you have a question about the WB-20 and is the answer not in the manual?
Questions and answers