Table of Contents
Advertisement
Quick Links
PORTABLE MAGNETIC DRILLING MACHINE
Read this manual carefully before operating your Nitto Kohki
Portable Magnetic Drilling Machine. Keep this manual with
your machine. All users of the Nitto Kohki Portable Magnetic
Drilling Machine must read this manual.
ATRA ACE
Professional Tool
Model
Power Supply (Single Phase)
Rated Power Consumption
Rated Current
Drill Motor
No-load Speed
Load Speed
Magnet Power Consumption
JETBROACH One-touch type
Hole Capacity
HI-BROACH One-touch type
AUSTBROACH
Magnet Holding Power
Magnet Size
Weight
change without prior notice due to improvements we are making day in, day out.
Model AO-5575A
For One-Touch Type Annular Cutter Only
(Side-Lock Type Annular Cutter cannot be used.)
Max. Hole Diameter 55 mm dia.
Max. Plate Thickness 75 mm
Max. Hole Diameter 50 mm dia.
Max. Plate Thickness 50 mm
Manufactured by :
9-4, NAKAIKEGAMI
2-CHOME, OHTA-KU,
TOKYO, 146-8555, JAPAN
Tel : +81-3-3755-1111
Fax : +81-3-3753-8791
AO-5575A
220-240 V AC 50/60 Hz
950 W
4.3 A
-1
520 min
-1
300 min
50 W
10 kN
86 × 170 mm
17.5 kg
Original Instructions
TQ15123-0 04/2017
Advertisement
Table of Contents
Related Manuals for Nitto Kohki ATRA ACE AO-5575A
Summary of Contents for Nitto Kohki ATRA ACE AO-5575A
- Page 1 PORTABLE MAGNETIC DRILLING MACHINE Read this manual carefully before operating your Nitto Kohki Portable Magnetic Drilling Machine. Keep this manual with your machine. All users of the Nitto Kohki Portable Magnetic Drilling Machine must read this manual. ATRA ACE Model AO-5575A...
-
Page 2: Table Of Contents
CONTENTS page GENERAL SAFETY RULES ………………………………… 2 T h a n k y o u v e r y m u c h f o r y o u r POWER TOOL SAFETY ……………………………………… 3 purchase of Before using your machine, please ABOUT YOUR NITTO PORTABLE MAGNETIC …………………………………………... -
Page 3: General Safety Rules
WARNING You must always wear suitable hearing protection Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains Always Wear respiratory protective equipment ● chemicals known [to the State of California] to cause (PPE) when working in an environment where dust cancer birth defects or other reproductive harm. -
Page 4: Power Tool Safety
authorized Nitto dealer. MAINTENANCE Always secure your work piece. Improperly mounted ● work can become loose. This can cause severe Do not attempt to disassemble or modify your ● magnetic drilling machine. Always use a vice or a clamp. Do not attempt to Do not modify your magnetic drilling machine. -
Page 5: About Your Nitto Portable Magnetic
If you have any doubt about the grounding of ● the magnetic drilling machine, contact a licensed electrician. Never connect the grounding conductor to a gas ● pipe. This will result in an explosion and severe Always check the grounding conductor. If you have ● ... - Page 6 The work piece must be at least 9 mm thick. If a ● ● work piece is too thin, the magnetic power of your There is always a possibility that magnetic power machine will decrease. This will cause the machine can be lost or reduced because of a power failure.
-
Page 7: Drilling Macine
The use of an engine-driven welder as a power ● source may cause your magnetic driven machine to malfunction, Power from an engine-driven welder can damage the electronic circuits in your portable drilling machine. Fig. 6 Do not use an extension cord that is too thin. Do ● ... -
Page 8: Application
1 APPLICATION 2 RECEIVING INSPECTION This is a portable drilling machine with a Magnet, Upon unpacking, check to see that the shipment is geared to drilling mild steel (mild steel or equivalent) complete without damage or oil leakage in transport. using One-Touch type Jet-Broach or Hi-Broach. -
Page 9: Part Names
Fig. 8... -
Page 10: Functions Of Electronic Control
5 MACHINE SETUP 4 FUNCTIONS OF ELECTRONIC CONTROL WARNING ● WARNING ● When the Magnet Switch is turned to ON, a lamp on the side of main body will light up in green. Mount the Side Handle on the Drill Motor. As the drilling operation load increases, the lamp will change in color from green to orange to red. - Page 11 Cutting Oil Safety Precautions WARNING WARNING ● CAUTION Use Cutting Oil for cutting purpose only. Don’t use it ● for household purposes ● The Cutting Oil contains amine. Do not mix it up ● with rust inhibitor, etc. containing nitrite. (1) Bring the Drill Motor up by turning the Rod Handle Wear safety glasses for eye protection when ●...
- Page 12 When storing Cutting Oil after use, put it into a Rod Handles can be positioned either on the right ● ● container and put a lid on for tight sealing so or left side of the machine, by changing the Pinion that dust or moisture, which is a catalyst for Shaft insert direction as follows;...
-
Page 13: Machine Operation
Put a rather large punch mark in the workpiece by WARNING driving a punch down with a hammer. The punch mark will be used as a guide for drilling operation ● that follows, so it must be made in accurate ●... - Page 14 WARNING CAUTION ● ● Turn on the Magnet Switch. The switch lamp will glow and magnetic power will come on. Open the P-Valve and turn the Rod Handle. Pilot (Fig.22) Mounting the Guard as shown. (Fig.21) Feed Slowly 2-3mm(5/64"~7/64") Guard (TB05418) Fig.
- Page 15 MAGNET MOTOR CAUTION push ● push Fig. 24 Fig. 25 Don’t proceed to the next operation without ● At the end of drilling operation slug will pop out ● Pin. Should a slug left in the hold sticking, remove ● it from the hole by tapping the collar of the slug with a needle stick or something.
-
Page 16: Troubleshooting
7 TROUBLESHOOTING WARNING ● ● The machine has electronic control. Be sure to turn off all the switches, pull up the electric drill, and then check the machine, when the operator come across to the following situations such as. Troubleshooting Switch lamp doesn’t come on Power supply plug is not connected to Connect power supply plug to socket. - Page 17 WARNING ● ● For the purpose of safety, when you don’t use the machine temporally or on a long-term basis, raise the Drill Motor and set it in position with the Set Screw so that it will not come down on its own Fig.
-
Page 18: Optional Parts
Cutting chips Hi-Broach 12 to 17 dia. Cutter TK01167 Pilot Pin 06025 Jetbroach 12 to 17 dia. TJ12696 Pilot Pin 08025 Hi-Broach 17.5 to 35 dia. TJ15859 Pilot Pin 08035 Jetbroach 17.5 to 40 dia. Pilot Pin Hi-Broach 12 to 18 dia. - Page 19 TB07474 Chip Breaker Ass’y Hex. Socket Head (TQ10787) Blade Cap Screw 6×10 (TQ10695) Blade Base Blade Base (TP14178) Hex. Socket Head Cap Screw 6× 10 (TP01945) Hex. Socket Head Cap Screw 5× 12 Blade (TP01939) Hex. Socket Screw Key 4 (TP04004) Hex.
-
Page 20: Ordering Parts
TK01154 12 ×50 TK00387 21.5×50 TK00400 30 ×50 TK00413 43 ×50 TK01155 13 ×50 TK00388 22 ×50 TK00401 31 ×50 TK00414 44 ×50 TK01156 14 ×50 TK00389 22.5×50 TK00402 32 ×50 TK00415 45 ×50 TK01157 15 ×50 TK00390 23 ×50 TK00403 33 ×50 TK00416... - Page 24 Overseas Affiliates / Offices NITTO KOHKI U.S.A., INC. NITTO KOHKI (SHANGHAI) CO., LTD. Shenzhen Branch 46 Chancellor Drive, Roselle, Illinois 60172, U.S.A. 2005C Shenzhen ICC Tower, Fuhuasanlu 168, For Cuplas Futian District, Shenzhen, Guangdong 518048, China Tel : + 1-630-924-5959...
Need help?
Do you have a question about the ATRA ACE AO-5575A and is the answer not in the manual?
Questions and answers