Advertisement
Quick Links
Advertisement
Summary of Contents for Apollo Bio-Full Face Mask
- Page 1 243-0424 046-233-4111 046-233-5886 E-mail cs@apollo-japan.jp http://www.apollo-japan.jp Nippon Sensuiki Co., Ltd 905 Shake, Ebina-City, Kanagawa-Pref, 243-0424, Japan 046-233-4111 046-233-5886 19. 11. 29 3704500028...
- Page 2 Introduction Thank you for choosing apollo bio-full face mask. As always be sure to obey articles described on instruction manual when in use. If you have any question, feel free to contact dealer or us. Items with the following headings describe scuba diving techniques and how to handle diving equipment.
- Page 3 DANGER It is extremely important that scuba divers using this product have undergone theoretical and practical training given by an internationally authorized association providing diving instruction. Never scuba dive alone. Always dive under the buddy system or under watching on ...
- Page 4 CAUTION Consult with dealer or us whenever using under special situation, environment. Do not disassemble except a portion described on the instruction manual. Necessary adjustment or replacement of parts should be performed on the land. The installation of the hose to the 1st stage should be done at shop purchased ...
-
Page 5: Names Of Parts
Names of parts Belt grip Strap holder Mask strap Strap adjuster Mask flange Mask frame Lens Lens retainer 2nd stage port Communication port Breathing port valve Water drain valve... -
Page 6: Specification
Specification / Item / Specification W 156 mm H 64 mm D 9 mm Dimension of mask frame W 144 mm H 190 mm D 88 mm Dimension of mask flange 450 g Weight 400 cc Inner volume Material of mask flange Silicone rubber Mask strap 5 straps with strap adjusters... - Page 7 Operation of the breathing port valve Breathing from regulator For diving, turn the knob of the breathing port valve clockwise until the valve is completely closed.. Breathing in open air For breathing, turn the knob of the breathing port valve counter-clockwise to open the valve.
-
Page 8: Mask Clearing
Strap adjustment To tighten the strap To tighten, pull the loose end of the strap. The strap can be adjusted while you are wearing the mask. To loosen the strap To loosen, pull the inside portion of the strap while pushing on the strap lock lever. - Page 9 Wearing the mask Turn the breathing port valve counter-clockwise to fully open the breathing port. While holding the strap adjuster knobs with thumb and forefinger, pull the straps to loosen. Rake hair back from the face, then wear the mask by holding the mask and the back portion of mask band.
- Page 10 Repeat the sequence of 6) through 7) to fine adjust the strap tightening so that the all straps are evenly strained without too tight. Finally move the strap holders in place. WARNING Make sure hair is not caught in the skirt portion of the mask. Remove the hair if there is caught hair.
- Page 11 Equalizing / Clearing ears Equalization can be done like normal diving mask by pinching the nose from over the mask. Pinch the nose with the thumb and forefinger from over the mask. Blowing gently to equalize the middle ear pressure to outer pressure. ...
- Page 12 Replacing the mask in water Remove all buckles, grasp the lower part of the mask with both hands, lift the mask upward and remove the mask. Put the removed mask on your arm etc. to avoid getting in the way. Change the regulator to the octopus, clear the regulator by breathing out or purge, then ensure normal breathing.
-
Page 13: Storage And Handling
Care After use, wash it with fresh water. During cleaning, do not press the purge button to prevent water from entering the regulator. When cleaning, remove foreign body such as sand and seaweed attached to buckles and valves. ... - Page 14 to use the communication port Attach OTS microphone assembly to communication port OTS Guardian Spectrum The microphone and its bracket of OTS Earphone/Microphone Assembly designed for OTS Guardian or Spectrum full face mask can be installed in the communication port of bio-full face mask.
- Page 15 P_OTS Attach the microphone blacket P_OTS over the neck, the narrow part, of the OTS microphone module. Then attache the support shaft to the microphone Blacket P_OTS over the OTS microphone module. OTS microphone P_OTS 5) OTS P_OTS Insert the OTS microphone and its bracket into he communication port.