Page 1
QUCM 3964(R) Application Manual QUCM 3964(R) Installation and Programming Manual This Manual describes the QUCM application for interfacing 3964(R) devices to a Modbus master. Effective: 17 April, 2001 Niobrara Research & Development Corporation P.O. Box 3418 Joplin, MO 64803 USA...
Contents 1 Introduction ......................... 5 2 Installation ..........................7 Module Installation ......................7 Software Installation ....................... 7 Serial Connections to the QUCM-L ................7 Port 1 to Modbus Master ..................7 Port 2 to the Personal Computer ................9 Loading the Applications into the QUCM ..............9 3964(R) to QUCM Port 2 .....................
Page 4
Tables Table 4-1 Server Index Table For EPE5-TCP ................17 Table 5-1 Module Lights ......................19 Table 5-2 User Light Definitions ....................20...
Introduction ® The Niobrara QUCM is a TSX Quantum compatible module that is capable of run- ning multiple applications for performing communication translations between serial protocols. This document covers an application that allows a Modbus RTU master to communicate with 3964(R) devices. This setup allows a Modbus master to be placed in a point to point configuration with a single 3964(R) device.
If connecting to a Modicon PLC, Port 1 of the QUCM-L will be set to be RS-232. The Niobrara cable MM2 is ideal for this connection since it includes an RJ45 RS-232 connection for the QUCM-L and a 9-pin male RS-232 Modicon-style pinout for the PLC.
1. The supported baud rates by both units are 1200, 2400, 9600, and 19200. 9600 baud is the default. Quantum QUCM QUCM-L Niobrara Fault Active Ready MM2 Cable MM1 Cable Figure 2-2 QUCM-L Layout 8 Installation QUCM 3964(R) Application Manual...
This link may be a serial connection from a COM port on the personal computer to the RS-232 port on the QUCM-S. The Niobrara MM1 cable may be used for this connection. This cable is shown in Figure 2-3.
Page 10
Will load the file into application 1’s flash and set the program to automatically start on power-up. Place Switch 1 in RUN. The RN1 light should come on. Place Switch 2 in HALT. Connect the Modbus master to QUCM port 1 with an MM2 cable. 10 Installation QUCM 3964(R) Application Manual...
The connection for the QUCM to the Euchner read/write head CIT3SX is an RJ- 45 connector on the QUCM side, and terminal screws at the Euchner device(Refer to Figure 2-4). RJ45 Terminal Screws Figure 2-4 QUCM-L RS-232 to Euchner read/write head CIT3SX QUCM 3964(R) Application Manual Installation 11...
To exit the Modbus configuration page, press the X key. This will return the user to the main configuration page. QUCM 3964(R) Application Manual Modbus to 3964(R) Bridge 13...
The message timeout feature allows the user to select how long the QUCM will wait for a reply to a query. The default timeout is 400ms. The timeout is fully programma- ble by typing the desired time in milliseconds. Valid times are 0 to 30000ms. 14 Modbus to 3964(R) Bridge QUCM 3964(R) Application Manual...
QUCM will receive the response at port 2, convert the message to Modbus RTU, and route back out port 1. The Bridge/MUX will re- ceive the reply, and route the appropriate Modbus Plus message back to the PLC. QUCM 3964(R) Application Manual Examples 15...
SMS-3000 Active Busy Error Modbus Drop = 101 IP Address IP Address 206.223.51.33 206.223.51.145 MM7 Cable Figure 4-2 Modbus TCP Example Table 4-1 Server Index Table For EPE5-TCP Drop TYPE Route OTHER 101,1 QUCM 3964(R) Application Manual Examples 17...
This light should not come on since there is no app2 loaded. Comes on when the module is transmitting on serial port 1. Comes on when the module is receiving on serial port 1. QUCM 3964(R) Application Manual Troubleshooting 19...
Lights when a Modbus message with opcodes 6 or 16(dec) is translated Not used Not used Not used Not used Not used Lights when application is in CONFIG mode Lights when application is in CONFIG mode Lights when application is in CONFIG mode 20 Troubleshooting QUCM 3964(R) Application Manual...