Veris E683 Series Installation Manual

Installation Guide
Power Metering CTs
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
• Do not use this product for life or safety applications.
• Do not install this product in hazardous or classified locations.
• Mount this product inside a suitable fire and electrical enclosure.
• Apply appropriate personal protective equipment (PPE) and follow safe electrical
work practices. See NFPA 70E in the USA, CSA Z462 or applicable local standards.
• This equipment must only be installed and serviced by qualified electrical personnel.
• Read, understand and follow the instructions before installing this product.
• Turn off all power supplying equipment before working on or inside the equipment.
• Product may use multiple voltage/power sources. Disconnect all sources before
servicing.
• Use a properly rated voltage sensing device to confirm that power is off. Do not
depend on this product for voltage indication.
• Current transformer secondaries must be shorted or connected to a burden at all times.
• Replace all doors, covers and protective devices before powering the equipment.
Failure to follow these instructions will result in death or serious injury.
Electrical equipment should be installed, operated, serviced and maintained only by
quali ed personnel. No responsibility is assumed by Veris Industries for any
consequences arising out of the use of this material. A quali ed person is one who has
skills and knowledge related to the construction, installation and operation of
electrical equipment and has received safety training to recognize and avoid the
hazards involved.
Installation, wiring, testing and service must be performed in accordance with all local
and national electrical codes.
If this product is be used in a manner not speci ed by the manufacturer, the
protection provided by the product may be impaired.
ZL0170-0A Page 1 of 2
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Aerospond, Veris, and the Veris 'V' logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
Rogowski Current Transducers
for use with E5xxxA & E2x Series Power Meters
Product Overview
The E683x Series of Rogowski flexible rope style current transducers (CTs) provide secondary AC voltage
proportional to the primary (sensed) current. For use with E5xxxA and E2x Series power meters, the E683x
Series CTs provide a cost-effective means to transform electrical service amperages to a voltage compatible
with monitoring equipment. The flexible core makes it easy to fit in tight enclosures.
These products provide reinforced insulation between the sensed conductor and the output leads.
Product Identification
Product
E683D502 Rogowski CT, 300 mm (12"), 600 Vac, 5 kA
E683G502 Rogowski CT, 460 mm (18"), 600 Vac, 5 kA
E683J502 Rogowski CT, 600 mm (24"), 600 Vac, 5 kA
E683L502 Rogowski CT, 900 mm (36"), 600 Vac, 5 kA
Specifications
Output at Rated Current
Operating Temperature Range
Storage Temperature Range
Max. Voltage L-N Sensed Conductor
Altitude of Operation
Installation Category
Limited Warranty
WARNING
Do not apply current transducers to circuits that have a phase-to-phase voltage greater
than their voltage rating unless adequate additional insulation is applied between the
primary conductor and the current transducers. Veris assumes no responsibility for
damage of equipment or personal injury caused by products operated on circuits
above their published ratings.
©2018 Veris Industries USA 800.354.8556 or +1.503.598.4564 / support@veris.com
Other companies' trademarks are hereby acknowledged to belong to their respective owners.
E683x Series
Description
Custom for E5xxxA and E2x Series power meters
Accuracy ±1% from 50 to 5000 A
Frequency Range 50/60 Hz
Cable 1000 Vac UL Style 21223 cable with 22 AWG leads
-15 to +60 °C (+5 to +140 °F)
-40 to +70 °C (-40 to +158 °F)
Humidity Range 0 to 95% non-condensing
600 Vac (reinforced insulation rating)
2000 m max.
COMPLIANCE INFORMATION
Approvals EN61010-1; UL61010-1; EN61010-2-032; UL61010-2-032;
CAN/CSA-C22.2 No. 61010-1
600 Vac Cat IV, Pollution Degree 2
WARRANTY
3 years
TM
0518